Saint NazaireFixed guide rail lifting cargo elevator,

The safety device and application of the guide rail hydraulic lifting platform The use of the guide rail hydraulic lifting platform The guide rail hydraulic lifting platform is a non-scissor hydraulic lifting freight elevator. It is used for goods between different floors of industrial plants, restaurants, restaurants, etc. The low height can be made to -mm. The advantage is that it can be placed directly on the ground without digging pits, reducing engineering construction costs, and there is no need to set up hanging points on the top, which is safe. Reliable; the hydraulic lifting platform adopts hydraulic transmission mode and can be non-calibrated according to customer needsSeveral types: Motor winding open circuit. When one of the motor windings is disconnected, or one of the parallel branches is disconnected, the three-phase current will be unbalanced and the motor will overheat.The surface of the brushes of each part should be kept clean, high quality and low price. Fire-resistant-waterproof-high temperature resistant, durable, safe and reliable.Saint Nazaire,The ripper does not move up or down or the lifting force is weak: the pressure adjustment of the relief valve does not meet the requirements and adjust the pressure to the required value; see the cleaning in item above for the internal leakage of the oil cylinder; the reversing valve is locked or internal leakage; The oil tank is blocked; the oil supply pump is faulty; the one-way valve checks the wear and damage of the one-way valve core and valve seat, and whether the one-way valve spring is fatigued or deformed.Mechanisms: Mechanisms such as tabletops, track grooves, wire ropes, chains, and pulleys are made of solid materials to ensure safety.Ottawa,Secondly, there must be no dirt on the friction surface. If there is dirt, it needs to be washed off with gasoline or thinner; the gear box, gearbox, external gear and other parts of the equipment and the hydraulic oil must be in accordance with the requirements in the table; Correctly maintain the hydraulic guide rail lift. Regularly check whether the wire ropes in each part are broken or loose. If this phenomenon is found, replace them in time. If there is any looseness, it should be tightened in time. The connecting bolts of the equipment should be checked for tightness when the body is under pressure. All connecting shafts should be equipped with cotter pins; check whether each mechanism is operating normally, whether there is noise or failure , to eliminate all faults in a timely manner; when installing, dismantling and adjusting the slewing mechanism of the equipment, it is necessary to pay attention to the parallelism between the reducer and the center line of the gear and the appropriate meshing gap; conduct a comprehensive inspection of the equipment regularly, whether the wires and cables are If there is damage, whether the motor is overheated, replace it in time and continue to run after troubleshooting; ensure that the bearings of the motor, each box,Saint NazaireSimple and fast lifting cargo elevator, distribution box and brushes must be kept clean, and the travel switch points of each safety device must be safe and reliable.The safety device of the guide rail hydraulic lifting platform The mechanical part of the guide rail hydraulic lifting platform mainly includes the hydraulic system and the mechanical device.The last thing to note is that, compared with the lifting platforms in some places, protective fences are generally added on the platforms. Since the lifting platforms are special equipment, the National Quality Inspection Bureau is very strict on this piece of inspection. All must be dismantled, so when the personnel ask you if you want to add a guardrail, don't blindly refuse, and consider whether it is necessary according to the site of use. In addition, you must have the 'People's Republic of Special Equipment Manufacturing License' and the 'People's Republic of Special Equipment Installation, Transformation and Maintenance License' to produce install, and maintain. Therefore you must ask whether the manufacturer has these two certificates.

In addition to the fixed mode, the elevator also has a vehicle-mounted mobile type. As the name implies, it combines the lifting equipment with the vehicle-mounted system. Such a lifting equipment is very flexible to move, and of course it is more useful. For example There is this kind of lifting equipment in the airport, and it is also possible to install this kind of equipment in stations or stadiums. Since it can be moved, the scope of operation is not limited to a certain place, and it can be used wherever lifting operations are required. It can be used. For example, when installing outdoor advertisements, the height of some advertisements is relatively high. At this time, mobile lifting equipment can be used to send billboards or staff to the designated height to work. This kind of equipment can also be divided into two types according to the driving mode: hydraulic lifting and electric lifting. The so-called hydraulic lifting is driven by hydraulic oil to reach a specified height. The electric mode is driven by a motor or geared to lift to A certain height, clean up the debris on the platform.safety requirements ,If the motor of the hydraulic lift is overheated, stop the machine in time and continue running after troubleshooting. The motor bearings must be in good condition.Unscrew the screw on the dust-proof hole outside the flange of the elevator, adjust the PCS system ring to align the side hole with the dust-proof hole and tighten the inner hexagon. After that, remove the motor shaft key.The use of elevators is not to maintain and overhaul after the equipment fails. It is necessary to maintain the equipment according to the correct maintenance and overhaul, and start with the preparation work to prevent all possible failures and accidents. I hope that the editor can summarize the knowledge points today. Help everyone.

Before using the aerial work platform, it is necessary to confirm whether the outriggers are well supported, and then proceed with the operation; the rollers and slideways confirm whether the roller slideways of the hydraulic lifting platform are dry, and if there is When drying the site,The motor connection is wrong. When the delta connection motor is wrongly connected into a star shape, the motor still runs with full load, and the current flowing through the stator winding will exceed the rated current, and even cause the motor to stop by itself. If it overheats, it will burn out. When the star-connected motor is wrongly connected into a triangle, or the motor with several coil groups connected in series to form a branch circuit is connected in parallel with two branches, it will cause the winding and core to overheat, and in severe cases, the winding will be burned.Drain the hydraulic oil of the hydraulic lift and discard it. Tighten the joint to take out the oil filter. After cleaning, clean it with compressed air, then put it back into the oil tank,Saint NazaireOutdoor guide rail type cargo elevator, and connect the pipeline.Mechanisms: Mechanisms such as tabletops, track grooves, wire ropes, chains, and pulleys are made of solid materials to ensure safety.Saint Nazaire,Frequently check the humidity of the aerial work vehicle that is prone to water accumulation. It is inevitable that the aerial work vehicle is driving in rainy and snowy weather, or on muddy roads. The bottom and some gaps and indoor floors are easy to accumulate sludge. If the owner does not clean it in time this will hide the moisture. Therefore, the outer edge of the wheel hub, the door, the corner of the bottom of the trunk, the key hole and the wiper frame and other areas should be checked regularly, and the drainage holes in the door and various parts should be kept unblocked to ensure that the car seat covers, carpets and floors are protected from humidity. Rusty fittings.Test the freight elevator every day to see if the freight elevator can operate normally.In addition to the fixed mode, the elevator also has a vehicle-mounted mobile type. As the name implies, it combines the lifting equipment with the vehicle-mounted system. Such a lifting equipment is very flexible to move, and of course it is more useful. For example There is this kind of lifting equipment in the airport, and it is also possible to install this kind of equipment in stations or stadiums. Since it can be moved, the scope of operation is not limited to a certain place, and it can be used wherever lifting operations are required. It can be used. For example, when installing outdoor advertisements, the height of some advertisements is relatively high. At this time, mobile lifting equipment can be used to send billboards or staff to the designated height to work. This kind of equipment can also be divided into two types according to the driving mode: hydraulic lifting and electric lifting. The so-called hydraulic lifting is driven by hydraulic oil to reach a specified height. The electric mode is driven by a motor or geared to lift to A certain height, but at present, hydraulic lifting platforms are more widely used.