Stability: The workbench should evenly withstand % of the MAX load capacity and be stable at the MAX elevation. There is air in front of the pilot valve of the elevator overflow valve noise overflow valve. The damping hole on the main valve core of the overflow valve is blocked by oil dirt, and the pilot valve and valve seat are matched without spring deformation or incorrect installation. The remote control port has excessive oil flow, and resonance occurs with components in the circuit. Troubleshooting: Strengthen sealing, repeatedly adjust the pressure exhaust and clean the valve body several times, Make the damping hole unobstructed, repair or replace the spring, replace the oil, and other components. The pressure setting of other components should not be similar to the pressure setting of the relief valve. . The noise of the elevator pipeline is usually caused by excessive dead bends or loose fixed sleeves in the hydraulic pipeline.Yeleniagura, Poland,Hydraulic cargo elevator sinking refers to the lifting of the cargo elevator equipment to a designated position, and after a period of time, the entire table surface will automatically descend by a certain distance under its own weight. The phenomenon of hydraulic cargo elevators naturally descending during the leveling process. This phenomenon is definitelyFor hydraulic cylinders in hydraulic elevators, it is not practical to change their effective working area A (equivalent to displacement) to adjust the speed. Generally, the speed can only be adjusted by changing the flow rate. For variable displacement motors, speed regulation can change both the flow rate and the motor displacement.Mali,After long-term use of the automatic lifting platform equipment, it is inevitable that some malfunctions will occur. In order not to affect work, it is necessary to promptly solve the difficulties in starting the motor and abnormal sounds. Generally, due to overload, insufficient power supply, and a small cross-sectional area of the power supply cable, the starting voltage drop is too large and the price of the cargo elevator is reduced.Before installation, the installation personnel should confirm the infrastructure such as the foundation and shaft, pay attention to alignment, leveling, and alignment points, and confirm that the foundation meets the requirements before construction.The undercut length of the weld mm should not exceed % of the weld seam, and the depth should not exceed .mm.

Voltage too low: Measure the starter voltage, with an allowable fluctuation range of± %.There are two installation methods for hydraulic freight elevator oil cylinders: jacking and lifting. The difference between jacking and lifting is that the placement direction of the oil cylinder is opposite, which is a qualitative problem and easy to arrange. The disadvantage is that the effective use of the oil cylinder can lift the same load, and the oil cylinder of the lifting mechanism is much larger than that of the lifting mechanism. Professional elevator manufacturers and other special products, old brands, with price advantages and guaranteed qualityAfter hours of elevator operation, carry out medium maintenance on the mechanical and electrical systems.Create brilliance,Solution: Check if the performance of the legs is good, even if the butter is polished to increase its properties.The manufacturer of the hydraulic cargo elevator tells you the reason and cleaning method: Reason: Overload cleaning method: Reduce the load to clean. Reason: The return valve is not closed. Cleaning method: Tighten the return valve to clean. Reason: The one-way valve of the manual pump is stuck and the return valve is malfunctioning. Cleaning method: Unscrew the bolt at the valve port of the oil pump, conduct maintenance, cleaning, and replace the cleaning hydraulic oil to clean.Reason: The lowering valve is not tightly closed. Cleaning method: Check if the lowering valve is powered on. If there is no power supply, clear the malfunction of the lowering valve itself or replace the lowering valve. It is necessary to keep the valve of the lowering valve clean and flexible.

Aluminum alloy elevators are different from other forms. This type of elevator is made of aluminum alloy material, which is lightweight and has a more beautiful appearance. The disadvantage is that it has a light load capacity and is only suitable for simple high-altitude maintenance work, and can only provide support for - people.resources,When installing, disassembling, and adjusting the rotating mechanism, attention should be paid to ensuring that the middle line is parallel to the middle line of the gear, and its meshing surface is not less than %. The meshing clearance should be suitable for the brakes of each mechanism. The clearance between the brake wheels should be regularly checked and adjusted to ensure its flexibility and reliability. There must be no dirt on the friction surface and it must be cleaned with gasoline or diluent.In addition, the convenience of the layout is also a very important issue. For example, in areas with large or high waves, there may be layout issues when using a lifting mechanism. At this point, in order to facilitate the arrangement and prevent the hydraulic cargo elevator cylinder from being eroded by waves,Yeleniagura, Polandhydraulic lift, during the lifting process of the cylinder as the lifting point of the bridge is not in a straight line during the lifting process. Therefore, the connection between the two ends of the cylinder and other components must be hinged in the same square. In addition, the installation of the hydraulic cargo elevator cylinder must also be determined through comparison and calculation, whether it is the tail lifting ear type, the middle pin shaft type, and the overall installation height is low. The disadvantage is that if the cylinder stroke is large,Yeleniagura, PolandHandmade children's hydraulic lifting platform, there may be stability issues with the cylinder, and the cylinder layout may be difficult. The main advantage of the hydraulic cargo elevator lifting mechanism is that it does not have a stable transmission installation frame for height measurement. Therefore, this form can be considered in places with large drops. The sudden deafness oil type on the head can reduce the installation height, but if it is too large, the oil cylinder will experience an increase in force due to the lifting height. Moreover, the higher the lifting height, the faster the increase in force, when it is too large the head pin type is not suitable. In order to comprehensively consider the height of the installation bracket and the force on the oil cylinder during the lifting process, an intermediate installation method can be considered, and the installation position can be set at an appropriate height according to calculations.Oil leakage from the oil cylinder: If it is a problem with the sealing ring, replace the sealing ring. If there are debris or debris on the oil cylinder, it is recommended to replace it with a new one.Yeleniagura Poland,Yeleniagura, Poland6-meter hydraulic lifting platform,The cylinder head oil seal is too tight or the rod is bent, which can also cause noise during movement due to other forces. At this point, the oil seal or straightening rod must be replaced in a timely manner.Considering the oil level in the oil tank, when all hydraulic cylinders in the system are extended, the oil level in the oil tank should not be lower than the Z-low oil level, and when the oil cylinders retract the oil level should not be higher than the Z-high oil level. In fact, most manufacturers have noticed the above issues. The reason for the introduction is that most users can learn more about the equipment itself when using elevators, in order to facilitate equipment maintenance. Hydraulic cargo elevator manufacturers sincerely hope that you choose a legitimate manufacturer when purchasing elevators, to avoid any worries about after-sales service.When the hydraulic oil of the equipment is insufficient, it will not cause lifting. At this point, you only need to add enough hydraulic oil to run.