also known as universal beam

I-beam, is a long strip of steel with I-shaped section. I-beam is divided into ordinary I-beam and light I-beam. It is a section steel with I-type section shape.The shape of small longitudinal crack on the surface of alloy pipe is less than mm The overall width is less than mm The depth is lower than .mm.Rafsanja,The monthly summary of the real estate industry shows that there is a significant positive correlation between the market sales and the long-term trend of the apparent consumption of galvanized pipe, but there will also be a backwardness of the market in a special stage, and after the backwardness of the market in stages, there will be a rapid decline in the moving average of the apparent consumption of galvanized pipe,As shown in the name, I-beam is an I-shaped section steel. The inner surface of the upper and lower flanges has an inclination, generally :, which makes the outer flange thin and the inner flange thick. Therefore, and it is difficult to give full play to the strength characteristics in application. Although the thickened I-beam has also appeared in the I-beam market,RafsanjaWhich is a good welded pipe manufacturer, the structure of the I-beam has determined its torsional performance. Remove defective pipes within the allowable length.→ wide flange and large lateral stiffness. Strong bending resistance.

→ compared with general section steel,RafsanjaHow much is 28b I-beam per ton, it has the advantages of low cost, high precision and small residual stress. It does not need expensive welding materials and weld detection, and saves about % of the manufacturing cost of steel structure.The storage of galvanized pipes should pay attention to several points. The first is the storage location. It cannot be placed in the open air, because in the open air, not only the safety of various products such as theft, but also corrosion problems will occur. Open air sites are vulnerable to various extreme weather conditions. Large amounts of rain or snow will erode the zinc coating on the surface to the greatest extent, which may lead to rust of the product. The second is the details of storage. It is not directly exposed to the sun. It shall be cooled and dried and shall not be stored with corrosive articles.→ wide flange and large lateral stiffness. Strong bending resistance.Welcome calls ,I-beam, whether ordinary or light, can only be directly used for bending members or lattice members on its Web because of its large and narrow section size and large moment of inertia difference between the two main axes on the section. It is not suitable for axial compression members and flexural members perpendicular to the web plane, so its application range is very limited. I-beams are widely used in buildings and other metal structures.I-beam is mainly used in building structure, curtain wall engineering,RafsanjaHow much is 600 welded pipe per meter, mechanical equipment and vehicle manufacturing.The wear resistance fracture toughness, impact toughness and bending strength under different process conditions were compared, and then the heat treatment process of GCrMo was determined. Development and application of ZYS- bearing damping and antirust oil. Bearing is a new type of multial damping and antirust oil. It takes refined mineral oil as the base oil and is equipped with various additives such as antirust and antifriction. Through comparison test, matching test with lubricating grease and user test, it is proved that ZYS- bearing damping and antirust oil has outstanding damping effect and good antirust lubrication performance.

I-beam, also known as universal beam, is a long strip of steel with I-shaped section. I-beam is divided into ordinary I-beam and light I-beam. It is a section steel with I-type section shape.Variable cost, Special rolling method. When it is difficult to roll the required I-beam by the usual rolling method for some reason, the special rolling method can be used to make full use of the skills of uneven deformation and pass design. For example, when the billet section is narrow and wide I-beam is required to be rolled, the wave rolling method can be used; for example, when the billet is wide and small I-beam is required to be rolled, the negative rolling method can be used Spread rolling, etc.The surface of cold galvanized layer is smooth dense and uniform. It has good mechanical properties and corrosion resistance. The consumption of hot-dip galvanized coating is between % - %. The galvanizing process is complex, but the thickness of single-sided coating, surface coating and double-sided coating is different, so the thin-walled pipe shall be galvanized. The zinc coating has strong protection and corrosion resistance.H-section steelRafsanja