Hundreds of degrees Celsius, which can save energy.High pressure oil pipe for diesel engine (gb-) is a cold drawn square pipe for high pressure pipe of diesel engine system.amora ,In & sigma; Expressed in%. The calculation formula is: where: L -- gauge length after sample breaking, mm; L -- original gauge length of sample, mm. Reduction of area (& psi;) in the tensile test, the percentage between the large reduction of the cross-sectional area at the reduced diameter and the original cross-sectional area after the specimen is broken is called the reduction of area. In & psi; Expressed in%. The calculation formula is as follows: where: S -- original cross-sectional area of the sample, mm; S -- small cross-sectional area at the reduced diameter after sample breaking, mm.Improve the positioning and pre bending steps, if necessary, to ensure that the web hunting problem does not occur when pressing parts. Change the shape of the surface pressure of the material to ensure the quality of the parts and avoid the non movement of the surface shape of the roll gap, resulting in uneven walking feeding.Asyut,Improve the positioning and pre bending steps, if necessary, to ensure that the web hunting problem does not occur when pressing parts. Change the shape of the surface pressure of the material to ensure the quality of the parts and avoid the non movement of the surface shape of the roll gap, resulting in uneven walking feeding.The other is designed with deformation angle, which can be regarded as DEG from round tube to square tube; To & deg; The bending deformation of angle, so the deformation angle & theta; It can accurately reflect the deformation degree of corners and edges. In the design process considering the influence of dimensional accuracy and metal work hardening, the distribution of deformation angle is usually larger at the beginning and middle passes, and then gradually decreases. In the pass formed directly by arc intersection, so the pass perimeter is different from that of the pipe blank. In order to ensure the dimensional accuracy, the fillet part of the pass needs to be corrected and calculated. Therefore, this method has higher design accuracy than other methods. However, due to the large amount of iterative calculation, this method is more suitable for pass design by computer. If you use a frame that deforms both horizontally and vertically, you can directly use the deformation angle & theta; Pass design.Ferroalloy is an alloy composed of iron and silicon, manganese,amora Galvanized steel square pipe,amora Specification and size of galvanized flat pipe, chromium, titanium and other elements. Ferroalloy is the raw material for steelmaking. It is used as deoxidizer and alloy element additive for steel in square tube steelmaking.

Square tube production most square tube processing is square tube pressure processing, resulting in plastic deformation of the processed steel (billet, ingot, etc.). According to the square tube processing temperature, the square tube can be divided into cold processing and hot processing. The main processing of square tube includes: rolling: the gap (various shapes) between the square tube metal blank and the rotating roll , because of the compression of the roll, the material section is reduced and the length is increased. This is a common production method for producing square tubes. It is mainly used to produce square tube profiles, plates and tubes. It is divided into cold rolling and hot rolling.Except for the thickening of wall thickness, the corner size and edge straightness of square pipe reach or even exceedSquare tube is made of different materials. It needs qualified inspection by relevant staff before leaving the factory. Square tube has a wide range of uses. Its main field is not only the construction industry, and cast the liquid cast iron into a cast square pipe. This kind of cast iron is called cast iron.The difference between hot-dip galvanized square pipe and cold-dip galvanized square pipe is mainly from the following aspects: the appearance of hot-dip galvanized square pipe is slightly rough compared with cold-dip galvanized square pipe; The appearance of cold galvanized square pipe is smooth and bright.Cleaning solvent and emulsion can clean the surface of square tube to remove oilPig iron refers to the product made by smelting iron ore in blast furnace. It is mainly used for steelmaking and square casting. Put the cast pig iron in the melting furnace to obtain cast iron (liquid), grease, agent and similar organic matter,amora Seamless galvanized square pipe, but it can not remove rust, scale welding, etc. on the surface of square tube, so it is only used as an auxiliary means in production.

In this period, the technology of continuous rolling pipe was not mature.Honesty is the foundation,Square tube is made of different materials. It needs qualified inspection by relevant staff before leaving the factory. Square tube has a wide range of uses. Its main field is not only the construction industry but also can be seen everywhere in our daily life. The service life of square tubes is mainly affected by surface treatment. I will explain the specific operations of surface treatment of square tubes.How to specify the yield point of square tube: if the stress decreases, the upper and lower yield points shall be distinguished. The unit of yield point is nmm (MPA). Upper yield pointBrinell hardness (HB), Rockwell hardness (HRC) and Vickers hardness (HV) are commonly used.amora ,Square pipe for conveying flammable and non flammable fluids, Standard No.: gbt (gbt - ). The representative material is l-l pipeline steel. It is mainly used to transport flammable and non flammable fluids. Low pressure or high pressure square pipes have high requirements. The purpose of large-diameter qb square pipe is qb square pipe, C-shaped steel and H-shaped steel. It is mainly used in the construction of simple plant, steel structure and other infrastructure. Qb square pipe is generally used as the frame and purlin of the plant. C-shaped steel Steel is an important support for the plant, and H-section steel is used as load-bearing. Especially in recent years, a large number of small and medium-sized enterprises have started to build spacious and bright plants. If traditional buildings are built, the time is slow, the work progress is affected, and the investment is large. For some small and medium-sized enterprises, if the investment in the plant is too high, the capital will be produced after operation Serious impact. The plant built with qb square tube, C-section steel and H-section steel has the characteristics of time saving, money saving and fast use. Therefore, the sales of qb square tube, C-section steel and H-section steel have increased significantly in recent years and become the first choice for plant construction. Qb square tube, C-section steel and H-section steel are mainly used in the construction of simple plant, steel structure and other infrastructure The qb square tube is used as the frame and purlin of the plant. The C-shaped steel is used as the important support of the plant, and the H-shaped steel is used as the load-bearing. Especially in recent years, a large number of small and medium-sized enterprises around the country have started to build spacious and bright plants. If the traditional buildings are built, the time is slow, the work progress is affected, and the investment is large. For some small and medium-sized enterprises Said that if the investment in the plant is too high it will have a serious impact on the capital after operation. The plant built with qb square pipe, money saving and fast use. Therefore, the sales of qb square pipe, C-section steel and H-section steel have increased significantly in recent years, even when the wrinkle around the part is determined to be less than the clamping force, and the gradual increase of the roll gap force can be. When drawing the cone and hemispherical components, it should be increased to increase the inner diameter of the inner plate and the tensile stress of the wrinkle drawbead. Adopt the principle of loosening after tightening to loosen after tightening and ask Question.Precision inner diameter square tubes for hydraulic and pneumatic cylinders (gb-) are cold drawn or cold-rolled precision square tubes with precision inner diameter for hydraulic and pneumatic cylinders.The pressurization size and time are the key to the success or failure of welding. If the square tube synthetic material is not pressurized, a large number of pores will be caused due to the pores of the material itself and the gas generated in the reaction. It is not allowed to leave the reactants in the weld, so it must be densified, usually pressurized during the reaction.