GB No. I-beam is in height, in leg width and in waist thickness.Using alloy pipe to produce ring parts can improve the utilization rate of raw materials, simplify the production and manufacturing process, and save raw materials and production and processing construction time, such as roller bearing ring throwing Nowadays, seamless steel pipe has been widely used to produce hydraulic jack sleeve.victoria,Galvanized pipe refers to the shape and high frequency of hollow square steel pipe welded by the back of the steel pipe during the hot rolling or cold rolling of galvanized steel plate or cold bending of galvanized steel plate, or before the galvanization of cold hollow pipe. Galvanized. Galvanized square pipe can be divided into hot galvanized pipe and cold galvanized pipe from the production process. This is because the two galvanized pipes are different, when the extrusion molding is used for mm diameter pipe fittings, the investment of machinery and equipment is less, so the raw material consumption is also very small, and the technology is relatively perfect. Once the tube size is increased, the cold extrusion method must have large cargo capacity and high-power machinery and equipment. Therefore, the automatic control system will be upgraded.Zacapa,Plan scheme : for high carbon steel with carbon content of more than .% and high chromium alloy pipe with chromium content of no less than %, the interval is min.H-section steelWhether I-section steel is ordinary or light, due to the relatively high and narrow section size, it can only be directly used for members bent in the plane of their web or form lattice stress members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application.

Ways to obtain surface compressive stress characteristics of alloy tubesWhat is galvanized pipeThe crack mainly occurs at -mm from the edge of the alloy pipe. The shape is several parallel vertical cracks of different sizes. The regularity is that the thicker the specification and model of the alloy pipe is The wider the width, the more serious the disadvantages.High quality and low price,Because all parts of I-beam are arranged at right angles, I-beam has the advantages of strong bending resistance, simple construction, cost saving and light structural weight in all directions,victoriaHow much is a ton of welded pipe, and has been widely used. The inner and outer sides of the flange of the I-beam are parallel or close to parallel, and the end of the flange is at a right angle so it is named parallel flange I-beam. The web thickness of I-beam is smaller than that of ordinary I-beam with the same height of web, and the flange width is larger than that of ordinary I-beam with the same height of web, so it is also named wide edge I-beam.Key technical characteristics of alloy pipeWhether I-section steel is ordinary or light, because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different so it can only be directly used for members bent in the plane of their web or form lattice stressed members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application. I-beam is widely used in buildings or other metal structures.

The flange of H-beam is of equal thickness, including rolling section and combined section composed of three plates welded. All I-beams are rolled sections. Due to poor production technology, the inner edge of the flange has a slope of : The rolling of H-beam is different from that of ordinary I-beam. Only one set of horizontal rolls is used. Because its flange is wide and has no inclination (or the inclination is very small), a group of vertical rolls must be added for rolling at the same time. Therefore its rolling process and equipment are more complex than ordinary rolling mills. The maximum height of rolled H-section steel that can be produced in China is mm, which exceeds the welded composite section.Marketing Department, Frame line crack Pickling: if the material cannot be removed after cleaning, pickling will be selected. Pickling of galvanized pipe is divided into chemical and electrolytic. How to prevent white rust of galvanized seamless steel pipe? It has a certain anti-corrosion effect on the pipeline.→ compared with the concrete structure, the I-steel structure can increase the service area by %, reduce the self weight of the structure by % - %, and reduce the structural design internal force.victoria,Under the action of thermal stress because the initial temperature of the surface layer is lower than that of the heart and the shrinkage is greater than that of the heart, the heart is pulled. At the end of cooling, the surface layer is compressed and the heart is pulled. That is, under the action of thermal stress, the surface of the workpiece is finally compressed and the center is pulled. This phenomenon is affected by factors such as cooling rate, material composition and heat treatment process. The faster the cooling rate, the higher the carbon content and alloy composition,victoria4. How much is a ton of galvanized pipe, and the greater the final residual stress. On the other hand, due to the change of microstructure during heat treatment, i.e. the transformation from austenite to martensite, the increase of specific volume will be accompanied by the expansion of workpiece volume, and each part of workpiece will undergo phase transformation successively, resulting in inconsistent volume growth and structural stress. The final result of the change of tissue stress is the tensile stress on the surface and the compressive stress in the center, which is just opposite to the thermal stress. The microstructure stress is related to the cooling rate, shape and chemical composition of the workpiece in the martensitic transformation zone.→ under the same section load, the weight of hot-rolled H steel structure is reduced by % - % compared with the traditional structure. Mixed pass system. According to the characteristics of rolling mills and products,victoriaHow much is I-beam per ton, in order to give full play to the advantages of their respective systems and overcome their disadvantages, mixed pass system is often adopted, that is, the combination of more than two systems. For example, straight leg cross rolling pass system is adopted for finished hole and front hole of finished product, and bent leg cross rolling system is adopted for other passes; or direct rolling system is adopted for rough rolling hole and straight rolling system is adopted for the last ~ finish rolling holes Leg oblique tie hole, etc.