The above is the correct sequence of impeller disassembly of submersible slurry pump. Because different types of pumps have some differences in structure, we also need to refer to the instructions when disassembling.　　It is not correct that it has no effect on us.Puli Khumri ,　　 the resistance shall be greater than megohm after filling with water. Turn on the power supply to test the steering and mark the continuous position.　　 install the front pump shaft first and then the rear bearing for the slurry pump of the filter press of the cylindrical bearing box.Panghyon-dong,　　 Selection of pipeline diameter: the selection of pipeline shall consider the one-time purchase cost long-term operation cost and operation reliability.　　 The standby submersible slurry pump shall roll the shaft / turn every week to make the bearing uniformly accept the static load and external oscillation. The building structure in the water pump room shall be reconstructed. Sound absorbing and isolating plates shall be installed around the wall and on the top of the machine room and fixed with light steel keel; The connecting holes between the machine room and other rooms are tightly blocked,　　About %), and motor power p=i × U indicates that high power and current will increase.

　　The development of submersible slurry pump is to adapt to increasingly complex working conditions, facilitate users to use, and its use mode is more flexible. And it fills a part of the gap in the application of slurry pump. When the submergence depth is deep and there is no better slurry outlet, that is, in the traditional slurry pump　　 The electric pump should not be used in flammable and explosive environment, nor should it pump flammable liquid. How to use the submersible non clogging sewage pump?　　The purpose is to inject liquid higher than . MPa from the water seal ring to prevent gas leakage into the pump when the suction inlet of the submersible slurry pump is in a vacuum state. When the water pressure in the pump is higher than . MPa, the sealing fluid .-. MPa higher than the pressure in the pump can be injected to seal and reduce leakagesafety requirements ,Puli Khumri Split vertical pipeline pump,　　The operating environment is different: the key difference between the submersible slurry pump and the vertical slurry pump lies in diving. During the operation of the vertical slurry pump, some parts intrude into the pit and cannot completely invade the slurry; The submersible slurry pump can completely penetrate below the slurry level.　　The above is the reason for the insufficient liquid supply of the water pump when it is in use, as well as the specific methods to deal with this situation. We should pay attention to the regular inspection of the equipment during normal use to ensure that it is in use　　 When the slurry pump fails to absorb water during operation, it may also be because the bottom valve is not opened. At this time, it is necessary to check whether the bottom valve is open and make corresponding adjustment.

　　If the pressure in the local area is equal to or lower than the vaporization pressure corresponding to the water temperature in the flow process,Puli Khumri Two stage slurry pump,Good reputation,Puli Khumri Vertical centrifugal slurry pump,　　Stability and reliability of seals between pump bodies.　　Sewage; QW series submersible sewage pumps are generally equipped with an elbow, and then connect the water pipe as required. We call them mobile, which are mainly used temporarily or do not need to be fixed.　　As an emerging product, the application of the submersible slurry pump is gradually becoming more and more widespread especially filling the gap in the application conditions of the traditional horizontal and vertical slurry pumps. At present, and the market recognition is continuously improving, especially meeting the needs of deep-water sand pumping and dredging. At present, the depth can reach meters.Puli Khumri ,　　 install a valve to inject water at the water inlet and outlet. This method is to install a valve on the water inlet pipe of the submersible slurry pump and connect the water pipe to inject water into the pump. This is a common and simple method.　　Extend service life. In fact, the submersible slurry pump is widely used in many lives, and there is a very important component water seal in the pump, which can separate the pump body from the motor, so it mainly plays a role in use　　The above is about how to replace the water seal of Boshan submersible slurry pump. In addition to the water seal, other parts of the pump also need to be replaced in time when they are damaged. Moreover, some parts of the pump are relatively easy to be damaged, so we need to replace them regularly during use　　Check whether it needs to be replaced.