Take mobile elevators for example, the same goes for them. Of course, during the internship, there may still be some questions about the elevator, but without contact, simply mastering some specific skills can effectively handle these questions.Operating cost advantage: Low failure rate. Due to the use of advanced hydraulic systems and good methods the failure rate of elevator operation can be minimized. Low power consumption: When the hydraulic elevator descends, it is driven by the pressure generated by its own weight, which greatly saves energy.Mesa,The above introduction to common faults of hydraulic boarding bridges can be said to be very detailed. I hope everyone can respond well to various problems after reading it.Regular inspection and maintenance, and troubleshooting are beneficial for improving work efficiency, extending equipment service life, and ensuring the safety performance of elevators.Marathia,MesaLifting platform hydraulic station,What are the common faults of hydraulic lifting platforms? The hydraulic lifting platform's oil cylinder is severely damaged, resulting in uneven lifting height of the oil cylinder. It is recommended to carefully check whether the oil cylinder is normal.Check the rollers, intermediate shafts and bearings; Oil cylinder pin and bearing; Equality and wear of the hinge shaft and bearings of the boom; Add oil to the above components for maintenance of outdoor elevators and factory elevators. Extend the service life of bearings.What should I pay attention to when starting a new mobile elevator? High priced and various specifications of scissor lift manufacturers welcome scrap merchants, industrial companies, enterprises, and power departments to visit and negotiate with the company!

Remove and disassemble the hydraulic lift cargo elevator lowering valve, blow out the plunger with compressed air, then install it and reinstall it.Any machinery needs to be maintained after use,Mesa5 ton hydraulic lifting platform, the editor will tell you how to maintain elevators after use. In order to maintain the good technical condition of elevator machinery, ensure the safe use of on-site construction machinery, extend the service life of equipment, and reduce mechanical failures, construction enterprises must maintain according to the relevant regulations According to maintenance regulations, maintaining, and cleaning the elevator, be sure to support the support rod.Service first,There are three movable plates on both sides of the adjustment plate, which can effectively avoid accidentally injuring the toes of operators when the adjustment plate is lowered, ensuring the safety of equipment use.The hook of the seat belt should not be hung on unstable or moving objects. High priced and various specifications of scissor lift manufacturers provide timely supply, with high cost-effectiveness, and have become the preferred brand for many wire products. Welcome to purchase!What are the installation precautions for elevators? The folding fence and cage of the elevator should be cleaned of the foundation surface, and the foundation bolts should be installed properly. If the construction elevator is installed on the floor a pad iron must be used below the screws to increase the force surface between the nuts and the floor to reduce the impact of the nuts on the floor; Insert steel plate shims of different thicknesses between the chassis and the foundation stone at the anchor bolts to adjust the verticality of the guide rail frame; Install three standard sections and measure the verticality of the guide rail frame using a theodolite to ensure the verticality of each main pipe in both directions. After adjusting the verticality of the guide rail frame, tighten the four foundation bolts; Adjust the verticality of the fence door frame as above and tighten the remaining anchor bolts; Install the buffer spring; Connect the other half of the fence to the front half with bolts; Adjust the verticality and tighten the anchor bolts as above, and release the brake on the motor inside the suspension cage. (For SC/ models, first install the suspension cage before installing the drive plate).

Fault analysis of mobile elevators: Mobile elevators cannot lift or have weak lifting force: overflow valve pressure regulation does not meet the requirements: adjust the pressure to the required value; Oil cylinder internal leakage: check or exchange oil cylinder components; Clamping or internal leakage of directional valve: Check or exchange valve components; If the oil level is too low and the oil inlet filter is blocked, add enough oil and clean the filter. The fuel supply pump has drawbacks: check or exchange the pump.query,No matter what problem occurs, if encountering an unsolvable problem with a hydraulic lifting platform, it is better to produce it quickly and conveniently, and guide the manufacturer to solve it. Please pay attention to safety precautions during maintenance.Unscrew the screws on the dustproof hole on the outer side of the elevator flange, adjust the PCS system ring to align its side hole with the dustproof hole, and tighten the inner hexagon. Afterwards, remove the motor shaft key.Once the freight elevator malfunctions, the maintenance unit shall arrive at the site within the specified time (the specific time is not specified in Beijing, but within minutes).Mesa,Operating cost advantage: Low failure rate. Due to the use of advanced hydraulic systems and good methods, the failure rate of elevator operation can be minimized. Low power consumption: When the hydraulic elevator descends, it is driven by the pressure generated by its own weight, which greatly saves energy.Firstly, it is necessary to use and operate the elevator correctly. The operators should receive systematic operation training: regular inspection of operating standards should be carried out, and any violations of elevator operation should be detectedWhen using, the four legs should be firmly supported on a solid ground (based on the walking wheel about to leave the ground), and sleepers can be used when necessary.