The blowpipe shall be perpendicular to the lead pipe during welding, and the flame shall be moved continuously to prevent local overheating and the flux from carbonizing before filler metal is added.In the first ten days of May, the overall order receiving quantity of Tianjin Hebei Henan Plate Plant was not ideal. According to the monitoring data, the overall order intake of medium and heavy plate mills in Tianjin Hebei Henan region in the first ten days of May remained stable and weak. Due to the weak market shock, the overall order intake of the spot steel market was relatively weak. The total quantity of orders received in the first ten days of May is only about tons, while at the end of April, the total quantity of post settlement agreements of main steel plants can exceed tons.Sataship,The evaporated zinc is immediately turned into zinc in the air, forming white smoke, which brings great difficulties to the operation and affects the health of welders. Therefore, in the places where decorative brass pipes are welded, ventilation and other protective measures should be strengthened. The poor weldability of brass will cause problems such as pores, zinc evaporation and so on.The blowing mouth of the welding tool should not be too small to avoid excessive concentration of heat.Kenema,The copper tube shall be heated and welded first, and then the joint shall be heated until the heated part turns dark red. At this time,SatashipGCR15 alloy round steel, when the filler metal contacts the tube, the filler metal shall melt.For small diameter pipes when using filler metal, the length of filler metal is allowed to be equal to the diameter of the pipe, which is enough to fill the weld crater. One of the five major application fields of red coppr plate T, red copper bar and red copper tube: copper is the most widely used and used in the electrical and electronic industries, accounting for more than half of the total consumption. Used for various cables and wires, motors and transformers, switches and printed circuit boards; In the manufacture of machinery and transport vehicles, it is used to manufacture industrial valves and accessories, instruments, sliding bearings, molds, heat exchangers, pumps, etc.The copper bar market declined steadily this week, with a decline of - yuan. Due to low pig iron inventory, some steel mills in Jiangxi have resumed purchasing recently, the steel market has been in shock and adjustment, and the merchants are unstable. Steel mills in Hebei, Tianjin and other regions have stopped producing pig iron for steelmaking. Now, it is mainly expected to make inquiries. However,SatashipTinned copper bar, due to the lower price of raw materials, the price of iron mills has been lowered.

Red copper inventory in key areas has risen continuously, but the total pressure is not big. From the current overall inventory situation of the main distribution centers Wu an, Jiangyin and Lecong, the inventory level remains relatively moderate, and the pressure on the market is relatively small. In Wu an market, according to the data, the total inventory of medium and thick plates in Wu an was close to tons, increasing by tons on a weekly basis. In late April, it reached tons lower in the year, down tons from the high level after the Spring Festival, and rose for three consecutive weeks. In terms of the ovquantity it should be said to maintain a relatively moderate level.The storage and transportation of copper tubes in summer should also be paid attention to when controlling the surface of copper tubes.[] Welding process of copper pipe Clean the end and seven ports of steel pipe with steel wool. Do not use abrasive cloth or abrasive paper to clean, because it will affect the clean interface and result in poor welding effect.Administration,Some steel mills in Liaoning are interested in purchasing pig iron, but the local resources are tight, and the iron mills quotations are on the high side, resulting in a stalemate between supply and demand. The demand for cast iron and ductile iron in Jiangsu, Shandong, Shanxi, Hebei, Henan and other regions is sluggish, and the inventory pressure of iron mills is increasing. As the price of raw materials decreases, the quotation of iron mills continues to decline. At present the demand and cost support are weak, and there is no positive boost. The short-term pig iron market is weak and difficult to change.The room temperature tensile strength of the annealed red copper sheet is ~ kgf/mm, and the Brinell hardness (HB) is ~First of all, we should set up a warehouse. The temperature in the warehouse should be generally kept at - ° C, while the humidity should be normal. The room should be kept ventilated.

Disadvantages: Due to loose tissue and high pressure resistance, the pipe is only used to produce small air conditioning copper rods.Installation requirements,It can be wrapped with moisture-proof paper for moisture-proof protection. It can also prevent oxidation to a certain extent. If cracks or serious corrosion are found, they must be isolated.It mainly refers to strengthening the research on copper pipe corrosion and formulating a complete and scientific copper pipe use plan.The market opened today. Although the performance of Zitong Pai futures was modest, the overall market has stopped. The market mentality has not changed much sincekend. The price is stable, but some specifications are subject to negotiation, and the negotiation range is about - yuan. The overall rhythm of the market is stable and cold. In the middle of winter, the overall market in Northeast China has entered the traditional off-season, and the overall market has ended with little improvement. All companies are selling goods. The inventory level in Shenyang is very low due to the inventory clearing and all construction sites have been closed. In addition to the transportation pressure brought by the low temperature,Sataship6061 aluminum tube, the market was bleak.Sataship,When stacking, it shall be stacked reasonably and placed first.The blowing mouth of the welding tool should not be too small to avoid excessive concentration of heat.The difference between hard copper tubes and soft copper tubes in use Hard copper tubes can only be used as straight tubes and cannot be bent. Therefore, they are generally used in power plants, switches of electrical equipment, and places where the connection points are far away and do not need to be bent. Compared with soft copper tubes, the price of hard copper tubes will be lower. Although the name of the soft copper tube is soft tube, it can also be used as a hard tube, so the soft copper tube is used in more places, and can be used in a straight tube way, asell as in a coiled tube way. The length of the copper tube can be longer if the coil is used. If the connection point is longer, it can be cut randomly according to the length, air conditioners and other places where bending pipes are needed. When we use copper, we need not consider the preservation problem unless we buy a small amount at home. For example, large manufacturers use copper units to buy a large number of copper pipes once so there will be a problem. I believe some people do not know how to store unused copper materials, Now let s ask our staff to introduce the storage method of copper for you.