Pay attention to check whether there are any broken wires and loose strands in the wire ropes of each part. If it exceeds the relevant regulations, it must be replaced immediately. The maintenance of the wire rope should be strictly in accordance with regulations.Anti-corrosion measures for the body of aerial work vehicles Pay attention to small scratches. The paint surface of aerial work vehicles is often corroded. In addition to common collisions, scratches, small rocks on the driving tires, there may also be a peeling paint spot, and a small rust will appear after a long time. Because most of these scars are small, they are easy to ignore. Therefore, check regularly, the engine compartment cover and its surroundings and once found,Drain the hydraulic oil of the hydraulic lift and discard it. Tighten the joint to take out the oil filter. After cleaning, clean it with compressed air, then put it back into the oil tank, and connect the pipeline.The boxes and distribution boxes of the hydraulic lift are always kept clean, and the dust on the electrical equipment is cleaned in time.Hoganas,Frequently check whether the various mechanisms are operating normally and whether there is any noise. If a fault is found, it must be eliminated in time.In addition, during installation, it is strictly forbidden to use hammers,SergeFactory freight elevator lifting, etc. to prevent damage to bearings or gears due to excessive axial force or radial force. Be sure to tighten the mounting bolts before tightening the force bolts. Before installation, clean the anti-rust oil on the motor input shaft, the positioning boss and the connection parts of the elevator with gasoline or zinc and sodium water. Its purpose is to ensure the tightness of the connection and the flexibility of operation, the motor still runs with full load,SergeIndoor cargo elevator, and the current flowing through the stator winding will exceed the rated current and even cause the motor to stop by itself. If it overheats, it will burn out. When the star-connected motor is wrongly connected into a triangle, or the motor with several coil groups connected in series to form a branch circuit is connected in parallel with two branches, it will cause the winding and core to overheat, and in severe cases, the winding will be burned.

Check the limit switch to see if all the limit switches are loose. If so, please tighten them. Pay special attention to the ultra-high protection stroke of the hydraulic lifting platform to avoid accidents caused by the equipment exceeding the high safety height; check the pins (ear pins and center pins) Check whether the nuts, nuts, screws, etc. are loose, if any should be reinforced immediately; ensure that the hydraulic lifting platform rises and falls smoothly; outriggers (for high-altitude operating platform)The main structure and application of the guide rail elevator adopt closed gear transmission. The large and small gears are made of steel. The design is calculated according to the fatigue strength of the tooth surface, and checked according to the bending fatigue strength of the tooth root. The bracket bracket is used to fix and support all the mechanical parts and some electrical components of the elevator box. It is mainly welded by side plates, connecting pipes and connecting pieces. You can choose any product, and the professional elevator factory has safe and secure transactions. At the same time, in order to reduce the weight of the bracket, many craft holes are designed on the two side plates. Because the worm gear mechanism has the advantages of large transmission ratio,SergeElevating cargo elevators require, compact structure, small impact load, stable transmission and low noise, it also has the characteristics of reverse self-locking. It can ensure that the transmission mechanism can self-lock when the motor is powered off during the process of transporting patients, so the worm gear reducer is selected. The involute worm is used, the material is steel, and the helical surface is quenched to improve the transmission efficiency and increase the wear resistance. The material of the worm gear is polyoxymethylene. The plastic worm gear has the advantages of good processing economy, stable transmission, vibration absorption and noise reduction, light weight, wear resistance and self-improvement, which makes the design of the elevator more humanized.The price is guaranteed, the service is guaranteed, the quality and performance of the product must be good. Do not accept the products of some manufacturers whose quality is not up to standard,As for the guide rail elevator installed outdoors, it is often exposed to rain and sunlight, so special attention should be paid to regular maintenance and inspection to avoid accidents.The contact opening and closing of the travel switch of each safety device must be reliable, and the contact arc crater should be polished in time.Prepare the foundation according to the foundation plan, pay attention to the alignment, leveling, and alignment to ensure the level of the foundation and various requirements for use.

How to effectively prevent electric shock by using a hydraulic lifting platform It is very common to add a leakage protector, and the cost is not high. It is both affordable and safe, and can effectively prevent electric shock.Superior quality, if you touch the power supply with your hands, it may cause lifting failure in light cases, or electric shock accidents in severe cases.Maintenance should be carried out on a regular basis and with designated personnel. It is divided into semi-monthly maintenance, monthly maintenance and annual maintenance. The content of each type of maintenance is different, but they must be done, and there are detailed records and signatures of both parties.The contact opening and closing of the travel switch of each safety device must be reliable, and the contact arc crater should be polished in time.Serge,Avoid working in an environment. In the event of rain, snow and other weather, the use of the hydraulic lifting platform should be stopped to prevent the occurrence of a short circuit, resulting in electric leakage and electric shock; non-professionals are strictly prohibited from disassembling electrical appliances such as hydraulic lifting platforms. In the event of an accident, you can’t disassemble without permission to eliminate the cause. You must report to the manufacturer for repair in time, inform the phenomenon of the accident and the manufacturer will guide you to complete the inspection or send someone to repair it; do not disassemble the appliance without permission! Professional elevator factory guarantees quality, guarantees service. Guarantees quality. Your satisfaction is our pursuit! Welcome to inquire.The wrong connection of the motor of the elevator When a coil coil group or one-phase winding is reversed, it will cause a serious imbalance in the three-phase current and cause the winding to overheat.The motor winding is short-circuited. When a short-circuit fault occurs in the motor winding, the short-circuit current is much larger than the normal operating current, which increases the copper loss of the winding, causing the winding to overheat and even burn out.