Potential energy pumping water up high. However, once the pump can not absorb water,Paoy petHorizontal non clogging sewage pump, the equipment is shaped like a decoration so what is the reason for this situation? How to solve it? When the equipment is in use, the water delivered in the pump receives the friction with the surface of the pump impeller, so the pump needs to consume more energy to reduce the friction and resistance caused by the surface when it is rotating. Water will slowly overcome it as it flowsPaoy pet, It is about % of the solid particles of the pump diameter. It has the characteristics of remarkable energy-saving effect, anti winding, petroleum automatic installation and automatic control. It has a unique effect in discharging solid particles and long fiber waste. Very suitable for chemical, pharmaceutical, mining, paper industry, cement Second, the power used is not matched, so the motor temperature will be too high after long-term overload operation; In addition, frequent startup during use will also lead to fever, so ISherbrooke, Other ysts believe that, at least in recent years, the situation of power shortage will continue, the contradiction between power supply and demand is still prominent in recent years, which is undoubtedly an opportunity for it and the generator industry. In water pumps and generators, especially The input quantity is related to many factors such as the rotating speed of the submersible slurry pump, the bearing standard, the continuous working time, the number of stops and starts of the pump, the surrounding environment and the working temperature. Therefore, it is necessary to gradually accumulate the experience and add smooth oil in a reasonable and timely manner. Selection of pipeline diameter: the selection of pipeline shall consider the one-time purchase cost, long-term operation cost and operation reliability.
When stopping the operation of the submersible slurry pump, close the cock of the vacuum gauge and pressure gauge and the gate valve on the water outlet pipeline, and After that, cut off the power supply of the motor. If the temperature of the environment is low, open the square plug at the lower part of the pump body to remove the remaining water to avoid frost cracking. During operation, the maximum temperature of the bearing shall not exceed ℃, and the quantity of calcium base grease used for lubricating oil bearing shall be the same as that of the bearing body The pipeline support is unstable and shakes. Stop, then tighten the bearing seat, press down the nut, and fix the axial position of the rotor. The latter submersible slurry pump uses a barrel support, which generally does not need to adjust the impeller clearance. Therefore, if there is a problem with the clearance in the future use, loosen the support clamp first, and say that the nut is looseAdministration, the water pipe shall be provided with a gate valve to regulate the pump working point. The valve shall be installed as close to the pump outlet as possible. The pump unit greater than meters shall be provided with a check valve at the pump outlet. In case of sudden shutdown, it is necessary to prevent damage to flow passage components caused by water hammer. In addition to the main impeller inside the equipment a set of impeller for mixing will be added at the bottom of the equipment, so that some mortar slowly settled inside the equipment can be mixed with water to become a flowing medium, so that the equipment can be used without its The bus voltage where the motor is located is V. Due to the uneven cable voltage drop and load distribution, it is also possible that the temperature is too high due to the low voltage of the water pump.
the water pipe shall be short, extending the service life of the pump. Water pump After understanding the cause of insufficient liquid supply,Paoy petBaigang deep well pump, we can solve the problem: First, we need to check whether the liquid level of the circulating liquid storage tank needs to add media to it.Paoy pet, If the head of the submersible slurry pump is too low or the head is higher than the practical condition, the flow will be large and the current will rise. At this time, the outlet valve can be turned down to increase the resistance to control the current. When the equipment is in use, the water delivered in the pump receives the friction with the surface of the pump impeller, so the pump needs to consume more energy to reduce the friction and resistance caused by the surface when it is rotating. Water will slowly overcome it as it flows Wheel, mixing impeller and other main flow passage parts are made of high wear-resistant raw materials, which are wear-resistant, corrosion-resistant, non clogging, and have strong sewage discharge capacity, and can effectively pass through large solid particles. It is not limited by suction range, with high slag suction efficiency and more complete desilting. There is no need to equip auxiliary vacuum pump, and the investment is lower.
This store is really good, with good quality and low price, the owner is very generous, and the customer service is also very patient. I don’t understand this Paoy petNon clogged pipeline sewage pump.
The boss is so kind, he really knows his job well. Under your guidance, I will soon become an expert! The seller's service is really attentive. Bring colleagues together in the future. Very good Paoy
The packaging Paoy petNon clogged pipeline sewage pump looks very good, the packaging is very careful, I believe the goods must be very good, thank you! Good value, huh, come again next time.
Your service is very good, Paoy petNon clogged pipeline sewage pump is also very cheap! I will come often in the future!
Paoy petNon clogged pipeline sewage pump Delivery is really fast, too efficient, the product has been received, give you a good comment.