Guide rail lift (also known as freight elevator) is a non-scissor hydraulic lifting platform, which is mainly used in industrial plants, restaurants, restaurants, warehouses, docks,MilesThe elevator is good, workshops and other places that need to move goods vertically between high-rise buildings above the second floor. The low height is especially suitable for sites where the site is not suitable for digging pits. What problems do we need to pay attention to in these places where elevators are used?Guide rail lift (also known as freight elevator) is a non-scissor hydraulic lifting platform, which is mainly used in industrial plants, restaurants, restaurants, warehouses, docks, workshops and other places that need to move goods vertically between high-rise buildings above the second floor. The low height is especially suitable for sites where the site is not suitable for digging pits. What problems do we need to pay attention to in these places where elevators are used?Miles,Relief valve: It can realize the effect of blocking the flow of oil passage and diverting flow. It is often used if the oil pipe bursts, causing the equipment to drop sharply and causing serious losses.When the freight elevator breaks down, professionals should be invited to repair it, and the freight elevator cannot be altered without authorization.Capine County,It is best not to cover the aerial work vehicle and park the vehicle outside. If it is windy and rainy, especially if the car blows sand on the clothes, when the wind does not directly spray powder or clean the sand on the mechanism, but it should be washed with water, and prevent the sand particles on the paint surface from being scratched by the vacuum cleaner.The use of the hydraulic lifting platform The user can choose the power mode and configuration according to his own scope of use: the power system includes: DC power supply, single-phase or three-phase power supply, and diesel engine.Correct construction elevator site inspection First of all, we need to check the foundation to see if there is any water accumulation, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, it can be divided into two types: open type and closed type. Of course, the lift also has a lot of safety equipment.

In the construction elevator, the switch box also has leakage protection equipment. Its wires and cables are well insulated, without leakage, and the metal threaded is not rusted, and its damage is close to zero. His steel wire rope should comply with the corresponding configuration requirements, and there is no problem of broken strands and diameter reduction. Of course, the number of broken wires should not exceed the corresponding standard. His pulley movement is very flexible.Make sure to add butter twice a month to the general transmission position where the grease fitting is located. For the parts that cannot be filled with butter, be sure to dredge the oil circuit or replace the grease fitting until the butter can be added, coil group or one-phase winding is reversed,After the goods are transported, clean up the debris on the platform.Use Hydraulic lifts are widely used in various industrial enterprises and production lines such as automobiles, containers, mold manufacturing, wood processing, chemical filling, etc., to meet the lifting needs of different operating heights,MilesFixed lifting cargo elevator, and can be equipped with various table forms (such as balls, rollers, Turntable, steering, tilting, telescopic) with various methods (separate, linkage, explosion-proof), with the characteristics of stable and accurate lifting, frequent starting, large load capacity, etc., effectively solving the difficulties of various lifting operations in industrial enterprises, so that Production operations freely. The professional elevator factory has advanced technology, strict testing, more affordable prices, and more discounts are in progress, welcome to consult.Conscientiously write the special construction plan for installation and construction, and make safety technical disclosures to the installers.

The boxes and distribution boxes of the hydraulic lift are always kept clean, and the dust on the electrical equipment is cleaned in time.Project scope,Regular maintenance Regularly check whether the circuit system of the hydraulic lifting platform is loose, and check whether the wires and cables are aging and damaged, this is the principle of using air compression to generate friction or electromagnetic effect to generate friction. It can be used to polish and remove rust on the rusty surface of the screw elevator table. It can be used for push rods of precision instruments or for Businesses that need to micro-operate screw jacks.The load of this series of products is divided into . to . tons it should be repaired in time to avoid electric shock.: Small pneumatic or electric rust removal, and can also be customized according to user requirements,Miles10 ton lifting cargo elevator, with a load of up to tons.MilesWhat is the new price of a fixed lift? Professionally improve the quality assurance of the freight elevator factory. The preferential activities are in progress, old brand and new and old customers are welcome to come to consult.Brake operators of various mechanisms on the equipment should regularly check and adjust the gap between the brake shoe and the brake wheel to ensure flexibility and reliability. Long-term promotion of freight elevator factory, price advantage, quality guaranteed!The use of elevators is not to maintain and overhaul after the equipment fails. It is necessary to maintain the equipment according to the correct maintenance and overhaul, and start with the preparation work to prevent all possible failures and accidents. I hope that the editor can summarize the knowledge points today. Help everyone.