The high-altitude work platform is a type of large-scale high-altitude work mechanical equipment. If you have any questions during use, you can directly consult our high-altitude work platform experts. Only correct use and regular maintenance can extend the service life of the high-altitude work platform, increase safety and reliability.The fault diagnosis equipment on the elevator can inform the operator of possible errors. The chassis is high and suitable for walking on rough surfaces. Planning is practical,GrujonzSelf made hydraulic lifting platform, reliable, and easy to repair and maintain. Diesel powered models have two wheel,GrujonzPit type lifting hydraulic platform, four wheel drive, and steering. Free turning equipment. Urgent descent system. The operation height ranges from meters to meters,GrujonzShear type hydraulic lifting platform, with advanced equipment and high-power power.Grujonz,In modern society, and their danger is not only related to construction management and personnel quality, but also to the working environment and equipment used in construction.Compact structure, small size in transportation status, able to enter the car of general elevators, as well as smooth door openings and narrow passages.Polichni　　Driving under the influence of alcohol is strictly prohibited, and ongoing high-altitude operations should also be terminated if feeling unwell.It is strictly prohibited to run the engine for a long time in a closed garage. The exhaust gas from the elevator engine contains carbon monoxide. This is a toxic gas that has been exposed to low concentrations of carbon monoxide for a long time. It can cause symptoms such as headache, shortness of breath, nausea and vomiting, body weakness and dizziness, psychological confusion, and even brain damage. In severe cases, it can cause death, such as starting the engine of the equipment in the garage.

The model of the elevator; The prices of different models of elevators vary.Platform part: It is a steel structure platform that carries heavy objects, which can be closed (i.e. car type) or open, with guide rollers or guide shoes installed on both sides. The bottom of the platform can be connected to a lifting oil cylinder or a lifting shear fork shaped steel frame.Drain all the hydraulic oil in the oil tank, open the oil tank, take out the oil suction filter, clean it and return it to the oil tank. Install it in its original position. Fill the fuel tank with new oil.Statistics,Check the rollers, intermediate shafts, and bearings; Oil cylinder pin and bearing; Equality and wear of the hinge shaft and bearings of the boom; Fill the above components with oil. The service life of bearings can also be greatly enhanced.Made of high-strength rectangular steel pipes, with good rigidity and stability. Equipped with universal casters for flexible mobility. The span of the two end brackets can be adjusted, which is suitable for crossing different obstacles. The two end brackets are vertically adjustable and can be used for operations on slopes or steps with a certain slope.The platform extends by . meters expanding the working range.

The double masted elevator adopts high-strength and high-quality materials, which have the advantages of beautiful appearance, small size, light weight, balanced lifting, safety and reliability. It is widely used in factories, hotels, restaurants, stations, airports, theaters, exhibition halls, and other places. It is a good safety partner for maintenance equipment, painting decoration, changing lighting fixtures, electrical appliances, cleaning and maintenance, and other purposes.Test conclusion,Drain and discard the hydraulic oil, remove the oil filter, clean it with compressed air, and then return it to the oil tank and connect the pipeline.The danger between rotating parts, such as the mechanism on the surface of certain flat printing machines.The single mast elevator adopts high-strength and high-quality materials, which have the advantages of beautiful appearance, small volume, light weight, smooth lifting, safety and reliability.Grujonz,We are well aware of the harm of pressure, but how can we prevent water from seeping into the hydraulic system of the elevator? After reading this article, you may know that oil contains excessive water impurities, which can rust the hydraulic components of the elevator, emulsify and deteriorate the oil, reduce the strength of the oil film, and accelerate mechanical wear. In addition to preventing water impurities from invading during maintenance, it is also important to note that when the oil storage tank is not in use, and the hydraulic oil of the elevator that is filtered each time needs to be replaced with a dry filter paper. In the absence of specialized instruments for detection, the oil can be dropped onto the hot iron plate, and no steam can be emitted before being added immediately. So when repairing the hydraulic system of aluminum alloy, be careful of the entry of moisture!We are well aware of the harm of pressure, but how can we prevent water from seeping into the hydraulic system of the elevator? After reading this article you may know that oil contains excessive water impurities, which can rust the hydraulic components of the elevator, emulsify and deteriorate the oil, reduce the strength of the oil film, and accelerate mechanical wear. In addition to preventing water impurities from invading during maintenance, it is also important to note that when the oil storage tank is not in use, the cover should be tightened and placed upside down; Oil with high water content needs to be filtered multiple times, the oil can be dropped onto the hot iron plate, be careful of the entry of moisture!During the rotation operation of the elevator it is necessary to raise the lower arm to a certain height before starting the rotation. The rotation should be slow, and attention should be paid to whether the distance between the shear arm and the platform to each equipment meets safety requirements.