System: explosion-proof electronic control system, remote control system, P IC system.Test the freight elevator every day to see if the freight elevator can operate normally.Toulouse,Introduction to fixed boarding bridge Loading and unloading mobile boarding bridge is a very easy-to-see structure in the modern logistics scene. It is the point and end point of the enterprise's logistics chain, and a loading and unloading operation platform for the enterprise's fast and turnover products and goods. The height of the loading and unloading operation platform is fixed, but there is always a certain height drop or gap between the height of the transport vehicles and the loading and unloading platform. As a result, the handling forklift cannot directly load and unload goods in and out of the transport vehicle. Utilize a boarding bridge to provide a reliable connection. It enables the forklift to move in and out of the transport vehicle efficiently and quickly for loading and unloading operations.Frequently check the humidity of the aerial work vehicle that is prone to water accumulation. It is inevitable that the aerial work vehicle is driving in rainy and snowy weather, or on muddy roads. The bottom and some gaps and indoor floors are easy to accumulate sludge. If the owner does not clean it in time, the door the outer edge of the wheel hub, the corner of the bottom of the trunk, the key hole and the wiper frame and other areas should be checked regularly, and the drainage holes in the door and various parts should be kept unblocked to ensure that the car seat covers, carpets and floors are protected from humidity. Rusty fittings.Klerksdorp,Naturally connect the motor to the lift. When connecting,ToulouseGuide rail chain lifting cargo elevator, it must be ensured that the concentricity of the output shaft of the elevator is consistent with that of the input shaft of the motor, and that the outer flanges of the two are parallel. If the concentricity is inconsistent, it will cause the motor shaft to break or the elevator gear to wear.The daily maintenance of the hydraulic lifting platform in normal use is essential, but even if there is normal maintenance on the equipment, any possible problem cannot be ignored,ToulouseGuide rail type lifting cargo elevator, so in order to ensure that the process of using the hydraulic lifting platform for each operation What aspects do we need to check before operation? Today, the editor will give you a popular science.Today, the editor will talk about a series of safety devices and their uses on the guide rail hydraulic lifting platform.

The elevator is a kind of elevator equipment composed of traveling mechanism, hydraulic mechanism, and enters the lower end of the hydraulic cylinder through the oil filter, explosion-proof electromagnetic reversing valve, throttle valve, hydraulic control check valve, and balance valve, so that the upward movement of the hydraulic cylinder can lift heavy objects The oil returned from the upper end of the hydraulic cylinder returns to the oil tank through the explosion-proof electromagnetic reversing valve, and the rated pressure relief valve is adjusted, and the pressure gauge reads the pressure gauge.The manufacturer adjusts the relief valve of the hydraulic lifting platform to the best state before delivery. If the customer adjusts it at will during use, it will cause the internal pressure to fluctuate. In severe cases, the service life of the motor will be shortened; Especially in summer, it is easy to burn out the circuit; Do not underestimate these actions, the service is guaranteed, and it is a large-scale logistics and storage equipment service company directly operated by the manufacturer. Since the fixed lift is a mechanical device, the quality and performance of the product must be good. Do not accept the products of some manufacturers whose quality is not up to standard, so as to avoid some safety hazards in use.Installation conditions,It is strictly forbidden for personnel to take the freight elevator to go up and down floors and climb.As for the guide rail elevator installed outdoors, it is often exposed to rain and sunlight, so special attention should be paid to regular maintenance and inspection to avoid accidents.It is strictly forbidden to switch the electric control switch with wet hands. Many people tend to ignore this detail. Although the safety voltage of the hydraulic lifting platform is below V, if you touch the power supply with your hands, it may cause lifting failure in light cases,ToulouseTwo story cargo elevator, or electric shock accidents in severe cases.

Always check all wires and cables for damage. The damaged part should be bandaged and replaced in time.Discount,The elevator is a kind of elevator equipment composed of traveling mechanism, hydraulic mechanism, electric mechanism and supporting mechanism. The hydraulic oil is under a certain pressure formed by the vane pump and enters the lower end of the hydraulic cylinder through the oil filter, explosion-proof electromagnetic reversing valve, throttle valve, hydraulic control check valve, and balance valve, so that the upward movement of the hydraulic cylinder can lift heavy objects , The oil returned from the upper end of the hydraulic cylinder returns to the oil tank through the explosion-proof electromagnetic reversing valve, and the rated pressure relief valve is adjusted, and the pressure gauge reads the pressure gauge.The hydraulic torque converter and compensation system are faulty, such as hydraulic torque converter failure, power shift failure, etc. The hydraulic torque converter is weak, the hydraulic oil volume is insufficient, the pressure is not properly adjusted, and the back pressure is insufficient. Check Torque converter oil quality (whether hydraulic transmission oil is misused), dosage, check torque converter pressure regulating valve, back pressure valve and its set pressure value Power shift failure. Quick return valve, pressure reducing valve, power transmission valve, The reversing valve is stuck and internal leakage. The oil pollution is serious. Check the cause of the valve stuck and eliminate it accordingly. Filter or replace the hydraulic oil. If the oil temperature rises too much, check whether there is any problem with the cooler check the quality of the hydraulic oil and the brand hydraulic The boarding bridge is also called a hydraulic loading and unloading platform, which can realize fast loading and unloading of goods. It has a simple structure design, flexible and convenient use, and high work efficiency. It is widely used and popularized in the market.In addition to the fixed mode, the elevator also has a vehicle-mounted mobile type. As the name implies, it combines the lifting equipment with the vehicle-mounted system. Such a lifting equipment is very flexible to move, and of course it is more useful. For example There is this kind of lifting equipment in the airport, and it is also possible to install this kind of equipment in stations or stadiums. Since it can be moved, the scope of operation is not limited to a certain place, and it can be used wherever lifting operations are required. It can be used. For example, when installing outdoor advertisements the height of some advertisements is relatively high. At this time, mobile lifting equipment can be used to send billboards or staff to the designated height to work. This kind of equipment can also be divided into two types according to the driving mode: hydraulic lifting and electric lifting. The so-called hydraulic lifting is driven by hydraulic oil to reach a specified height. The electric mode is driven by a motor or geared to lift to A certain height, but at present, hydraulic lifting platforms are more widely used.Toulouse,Before using the aerial work platform, it is necessary to confirm whether the outriggers are well supported, and then proceed with the operation; the rollers and slideways confirm whether the roller slideways of the hydraulic lifting platform are dry, and if there is When drying the site, an appropriate amount of butter should be added to ensure the smoothness during operation and to avoid head-to-head wear between mechanical parts.The contact opening and closing of the travel switch of each safety device must be reliable, and the contact arc crater should be polished in time.Pay attention to check whether there are any broken wires and loose strands in the wire ropes of each part. If it exceeds the relevant regulations, it must be replaced immediately. The maintenance of the wire rope should be strictly in accordance with regulations.