The cleanliness of the hydraulic station is an important aspect of the elevator hydraulic station, so it should not be careless. Moreover, from a professional point of view, there are relevant rules and requirements, and you should refer to the specification manual, so that you can have a correct understanding and know how to achieve better cleanliness.Naturally connect the motor to the lift. When connecting, it must be ensured that the concentricity of the output shaft of the elevator is consistent with that of the input shaft of the motor, and that the outer flanges of the two are parallel. If the concentricity is inconsistent, it will cause the motor shaft to break or the elevator gear to wear.Page numberA brief talk about the daily maintenance and use of the motor of the hydraulic lifting platform. Overloading is strictly prohibited. Overloading will increase the burden on the motor, and in severe cases it will cause the motor to burn out.What is the new price of fixed lifts? Fixed lifts are currently very popular in the market. Due to different manufacturers, different materials,Page numberGuide rail type lifting cargo elevator, different rated loads, and different brand awareness, the prices are also different. The current price of fixed lifts produced in the domestic market: rated load - tons, height of meters, table size mm *mm, the price is about - yuan; the rated load is - tons, the height is meters, the table size is mm*mm, the price is about yuan. Rated load,Page numberTwo ton guide rail type cargo elevator, lift height, table size of each fixed liftDifferent. (Specific bearing capacity and rising height can be customized according to user requirements)Nowshera Cantonment,This kind of fixed lifting equipment can also be used in the warehouse. For example, a certain floor in the warehouse needs to be lifted to send goods or personnel into the designated warehouse.System: explosion-proof electronic control system, remote control system, P IC system.Goods should be stacked on the platform and not tilted. When the freight elevator goes up and down beyond the range of the platform no one should stand around to watch.

Before using the aerial work platform, it is necessary to confirm whether the outriggers are well supported, refer to the level beads on the equipment to judge and debug, and then proceed with the operation; the rollers and slideways confirm whether the roller slideways of the hydraulic lifting platform are dry, and if there is When drying the site, an appropriate amount of butter should be added to ensure the smoothness during operation and to avoid head-to-head wear between mechanical parts.The daily maintenance of the freight elevator should be carried out by a professional team (issued by the State Administration of Quality Supervision).Naturally connect the motor to the lift. When connecting, it must be ensured that the concentricity of the output shaft of the elevator is consistent with that of the input shaft of the motor, and that the outer flanges of the two are parallel. If the concentricity is inconsistent, it will cause the motor shaft to break or the elevator gear to wear.resources,It is best not to cover the aerial work vehicle and park the vehicle outside. If it is windy and rainy, the clothing will repeatedly slap the car paint,Page numberFactory lift cargo elevator, especially if the car blows sand on the clothes, it will draw many fine scratches on it. Because it will turn black over time. In addition, when the wind does not directly spray powder or clean the sand on the mechanism, but it should be washed with water, and prevent the sand particles on the paint surface from being scratched by the vacuum cleaner.The safety device of the guide rail hydraulic lifting platform The mechanical part of the guide rail hydraulic lifting platform mainly includes the hydraulic system and the mechanical device.What is the new price of fixed lifts? Fixed lifts are currently very popular in the market. Due to different manufacturers, different materials different rated loads, and different brand awareness, height of meters, the height is meters the table size is mm*mm, the price is about yuan. Rated load, lift height, table size of each fixed liftDifferent. (Specific bearing capacity and rising height can be customized according to user requirements)

Unscrew the screw on the dust-proof hole outside the flange of the elevator, adjust the PCS system ring to align the side hole with the dust-proof hole, and tighten the inner hexagon. After that, remove the motor shaft key.offer,The last thing to note is that, protective fences are generally added on the platforms. Since the lifting platforms are special equipment, the National Quality Inspection Bureau is very strict on this piece of inspection. All must be dismantled so when the personnel ask you if you want to add a guardrail, don't blindly refuse, you must have the 'People's Republic of Special Equipment Manufacturing License' and the 'People's Republic of Special Equipment Installation, Transformation and Maintenance License' to produce, install, and maintain. Therefore, you must ask whether the manufacturer has these two certificates.The operating rod is heavy. The operating rod mechanism is faulty. Check, adjust, and replace unqualified parts; clean the valve parts; check the hydraulic oil cleanliness and the valve core is stuck (manufacturing, installation problems, dirt problems)The motor connection is wrong. When the delta connection motor is wrongly connected into a star shape, the motor still runs with full load, and the current flowing through the stator winding will exceed the rated current, and even cause the motor to stop by itself. If it overheats, it will burn out. When the star-connected motor is wrongly connected into a triangle, or the motor with several coil groups connected in series to form a branch circuit is connected in parallel with two branches, it will cause the winding and core to overheat, and in severe cases, the winding will be burned.Page number,It is strictly forbidden to switch the electric control switch with wet hands. Many people tend to ignore this detail. Although the safety voltage of the hydraulic lifting platform is below V, if you touch the power supply with your hands, it may cause lifting failure in light cases, or electric shock accidents in severe cases.It is strictly forbidden for personnel to take the freight elevator to go up and down floors and climb.What kind of function can be achieved by installing the elevator? Before installation, confirm whether the motor and the elevator are intact, and strictly check whether the dimensions of the parts connected to the motor and the elevator match. Here are the dimensions of the positioning boss of the motor, the input shaft and the groove of the elevator. Fitting tolerances.