Precautions for elevator installation Keep the access road of the external construction elevator smooth and have enough parking space for equipment. When it is necessary to use a steam crane for auxiliary installation, it should be fully considered whether the site environment meets the operating conditions of the steam crane.Anti-corrosion measures for the body of aerial work vehicles Pay attention to small scratches. The paint surface of aerial work vehicles is often corroded. In addition to common collisions, scratches, small rocks on the driving tires, there may also be a peeling paint spot, and a small rust will appear after a long time. Because most of these scars are small, they are easy to ignore. Therefore, check regularly, the engine compartment cover and its surroundings, and once found, go to a professional beauty shop for processing.Zaleg szeger,The lifting platform has been inspected and debugged before leaving the factory, and all technical indicators meet the design requirements. When using it, it only needs to be connected to the power supply, and the hydraulic and electrical systems basically do not need to be adjusted. Our company is engaged in all kinds of materials such as elevator factories all the year round, and operates with integrity. Welcome to call!Before using the aerial work platform, it is necessary to confirm whether the outriggers are well supported, refer to the level beads on the equipment to judge and debug, and then proceed with the operation; the rollers and slideways confirm whether the roller slideways of the hydraulic lifting platform are dry, and if there is When drying the site, an appropriate amount of butter should be added to ensure the smoothness during operation and to avoid head-to-head wear between mechanical parts.Traun,Naturally connect the motor to the lift. When connecting, it must be ensured that the concentricity of the output shaft of the elevator is consistent with that of the input shaft of the motor, and that the outer flanges of the two are parallel. If the concentricity is inconsistent, it will cause the motor shaft to break or the elevator gear to wear.Pay attention to check whether there are any broken wires and loose strands in the wire ropes of each part. If it exceeds the relevant regulations, it must be replaced immediately. The maintenance of the wire rope should be strictly in accordance with regulations.How to effectively prevent electric shock by using a hydraulic lifting platform It is very common to add a leakage protector, and the cost is not high. It is both affordable and safe, and can effectively prevent electric shock.

The contact opening and closing of the travel switch of each safety device must be reliable,Zaleg szegerSimple lifting cargo elevator, and the contact arc crater should be polished in time.Maintenance should implement the 'Special Equipment Supervision Regulations', 'Elevator Maintenance Rules' (GB and related national standards, industry standards and local standards.Hydraulic pump station: special pump station for domestic lifting platform, protection device outside the pump station imported from Italy: organ m type, mesh type, iron plate seal type.production costs,Unscrew the screw on the dust-proof hole outside the flange of the elevator, adjust the PCS system ring to align the side hole with the dust-proof hole, and the dust on the electrical equipment is cleaned in time.Frequently check whether the various mechanisms are operating normally and whether there is any noise. If a fault is found remove the motor shaft key.The boxes and distribution boxes of the hydraulic lift are always kept clean, it must be eliminated in time.

Today, the editor will talk about a series of safety devices and their uses on the guide rail hydraulic lifting platform.Packaging strategy,The water cooling of the hydraulic station is generally tube-type water cooling, and its type selection is based on the heat load to calculate the heat exchange area, while its air-cooled elevator is carried out by using an air cooler, and it is The heat transfer capacity is calculated according to the heat load, and then the type selection calculation is carried out under the condition that the flow rate can be satisfied. Therefore, mutual benefit and win-win. If you choose the wrong supplier, you will be overwhelmed with all kinds of after-sales troubles in the later stage. Recently, I have seen many netizens report the problem of very loud oil cylinders. Today, the editor will simply popularize the knowledge for everyone.There are foreign objects inside the oil delivery pipe of the hydraulic lifting platform,Zaleg szegerThe cargo elevator is, which causes uneven force on the hydraulic oil delivery, and uneven table tops. It is recommended to carefully check whether the oil delivery pipe is unblocked.Always check the connections of the various parts of the hydraulic lift, and tighten them if they are loose. The tightness of the connecting bolts of the body should be checked when the body is under pressure.Zaleg szeger,What is the new price of fixed lifts? Fixed lifts are currently very popular in the market. Due to different manufacturers, different materials, different rated loads, and different brand awareness, the prices are also different. The current price of fixed lifts produced in the domestic market: rated load - tons, height of meters, table size mm *mm, the price is about - yuan; the rated load is - tons, the height is meters,Zaleg szeger3-meter cargo elevator, the table size is mm*mm, the price is about yuan. Rated load, lift height, table size of each fixed liftDifferent. (Specific bearing capacity and rising height can be customized according to user requirements)The last thing to note is that, compared with the lifting platforms in some places, protective fences are generally added on the platforms. Since the lifting platforms are special equipment, the National Quality Inspection Bureau is very strict on this piece of inspection. All must be dismantled so when the personnel ask you if you want to add a guardrail, don't blindly refuse, and consider whether it is necessary according to the site of use. In addition, you must have the 'People's Republic of Special Equipment Manufacturing License' and the 'People's Republic of Special Equipment Installation, Transformation and Maintenance License' to produce, install, and maintain. Therefore you must ask whether the manufacturer has these two certificates.Safety performance: The lifting structure is made of high-strength manganese steel rectangular tube, with strong stability and high carrying capacity. The maximum lifting height is about meters and the scissor-type mechanical mechanism is easy to maintain, and the maximum load is about tons. .