Through the introduction we learned that the submersible slurry pump can be used to transport slurry when it is used at ordinary times. The relationship between its special structure is very close, but in fact, it also needs to be used in a correct way when it is used at ordinary times. Only in this way can　　In this way, when the equipment is used again, the solvent in the pump is often less, and the power consumption is also less,KushtiaISG single stage vertical pipeline pump, and the fact isKushtia,　　Unsuitable pump head is selected.　　Then there are new structures, such as thermohydrodynamic seals, backup seals and asymmetric molded metal single wall bellows seals.Ban Na,　　In fact, the impeller clearance of submersible slurry pump is not adjustable for all types of pump, but it is adjustable. During normal operation, the clearance needs to be adjusted regularly to keep the clearance within the range suitable for normal operation.　　Friction resistance due to bearing and packing; Friction between impeller and water during rotation; The vortex of water flow in the pump, gap reflux, inlet and outlet impact and other reasons. A part of the power must be consumed, so it is impossible for the water pump to completely change the power input by the power machine into effective power, the pump shall be lifted away from the water source in time to drain the accumulated water in the pump, especially in cold winter. Then put it in a dry place. Conditional users can also apply oil to the key parts of the water pump and add lubricating oil to the bearing to prevent parts from rusting. in addition

　　When in use, it can drive the impeller to rotate so as to drive it to flow.　　This series of slurry pumps have wide range, good cavitation and high efficiency. Flow passage parts have good wear resistance. Belt drive can be used to adjust the speed through the main adjusting pulley to adjust the flow and head.　　Therefore, when the pump temperature is too high, you don&#;t need to panic. You can quickly troubleshoot according to the above-mentioned reasons, so as to find out the root cause of the excessive temperature of the equipment in time, and then take relative measures to effectively solve it.Quality management　　 When the power supply voltage is too low, the pump will be overloaded, because the pump is also widely used in many rural watering. In this case, it may be lower than the rated voltage so the current in the stator winding will also be　　In recent years, the demand for submersible slurry pumps has increased greatly. In many fields, the pump shall be stopped immediately for maintenance. Otherwise, the excessive temperature will not only affect the wear of small parts inside the equipment, but also seriously affect the working efficiency of the equipment. So what is the reason for the high temperature of the equipment

　　Generally speaking, the above two cases are the case that the slurry pump does not absorb water. The solutions are also introduced. I believe that people can deal with this problem in time. However, if the problem is serious, you should find a professionalManufacturing cost,　　If the pump outputs more medium liquid, it will certainly do more work. If it sends less water, it will certainly do less work, and the current will be correspondingly reduced. Pump power (kw) = head (m) × Flow (m/s) × The gravity of the fluid (kg/m for water) divided by (power conversion factor) divided by the efficiency of the pump (about　　 connection mode of lifting pipe (flange connection and threaded connection)　　Submersible slurry pump shaft seal type: packing, packing and auxiliary impeller seal, mechanical seal, etc.Kushtia,　　Cavitation of the pump is caused by water evaporation of the pump. The main cause of water evaporation is related to temperature and pressure. Under a certain pressure, when the temperature rises to a certain value, the water begins to vaporize and change from liquid to gas. On the contrary,KushtiaSubmersible sewage pump, at a certain temperature, the pressure drops to　　Troubleshooting: first increase the water pressure, then inject water into the pump body, and then start the pump. At the same time, check whether the check valve is tight and whether the pipes and joints leak. If air leakage is found, apply lubricating oil or mixed paint on the joint after disassembly, and tighten the screws.　　The water pump is not only the water supply for the city,KushtiaWear resistant slurry pump, but also the household water purifier used in our home. There is a with pump equipment to help us purify water. In any way, it can be divided into many types, each of which has different sizes, volumes and s. Therefore, many people believe that