concrete strength, void ratio and shear span ratio on the shear capacity of concrete-filled steel tubular in pipe. It is found that the shear strength of members increases with the decrease of void ratio and the increase of concrete strength; The larger the shear span ratio, the smaller the shear strength. Combined with the test, the empirical formula of shear capacity of concrete-filled steel tubular in pipe is proposed, which is analyzed and verified by ABAQUS finite element modeling software. The results show that the simulation is in good agreement with the test results. In order to study the axial compression performance of stainless steel tube concrete conduit leg and the axial compression performance of stainless steel concrete conduit leg, experiments are used to verify the correctness of the finite element model. The load displacement curves of specimens in groups were compared, and the effects of different void ratio, concrete strength, diameter thickness ratio and bone index on the axial compression performance of concrete-filled stainless steel tubular short columns under axial compression were analyzed. The results show that with the increase of concrete strength, the bearing capacity of specimens increases, it is proposed to replace the four hollow steel conduit legs of the original offshore platform with concrete-filled steel tube in stainless steel tube to form a new composite offshore platform with concrete-filled steel tube in stainless steel tube the bearing capacity of the specimen decreases; The bearing capacity of stainless steel tube concrete can be effectively improved by adding steel bone; Increasing the bone matching index of steel bone can improve the bearing capacity of the specimen. Based on the jacket offshore platform, so as to improve the ice resistance and disaster prevention ability of the offshore platform. The scale test on the offshore platform shows that the composite offshore platform of concrete filled steel tubular in stainless steel pipe (hereinafter referred to as the composite offshore platform) has better anti icing performance than the ordinary jacket offshore platform. Taking push as an example, the peak acceleration and displacement of the upper deck of the composite offshore platform of concrete filled steel tubular in stainless steel pipe are reduced by % and % respectively. The analysis of ABAQUS finite element and experimental simulation results shows that the error of the two results can be basically within %. Through the simulation analysis of the ultimate bearing capacity of the stainless steel tube in tube concrete-filled steel tubular composite platform and the original offshore platform, it can be seen that the stainless steel tube in tube concrete-filled steel tubular composite platform has stronger ultimate bearing capacity. Therefore, the composite offshore platform of concrete-filled steel tube in stainless steel tube is a good new type of jacket offshore platform. Axial compression tests were carried out on austenitic and duplex stainless steel tube concrete short columns. The ultimate load, longitudinal strain and circumferential strain of the short columns under axial compression were measured. The effects of steel tube wall thickness and concrete strength on the bearing performance of the short columns were investigated. Reference was made to the European Code for design of concrete filled steel tubes (Eurocode), American code (ACI -) and Japanese code (aij-cft), China's relevant regulations D --dlt- and CECS calculate the preparation of stainless steel pipe construction, prepare construction scheme and construction schedule scheme, and establish quality standards.The intergranular corrosion of austenitic stainless steel can be prevented by adding Ti, Nb and other elements that can form stable carbides (tic or NBC) and avoiding the precipitation of crc on the grain boundary.Comitancillo,Cold formed alloys can be cut and cold formed. However, the alloy needs cold forming more than austenitic steel. Because of its high strength, springback should be fully considered.The accumulation of organic impurities caused by decomposition products and the pollution of some other metal impurities. There is no turnover of long-term stainless steel plate, stainless steel coil, stainless steel belt and stainless steel pipe to avoid price difference. The price is % higher than the market price! The price of more than one ton is higher! So that the nickel bath can not get the ideal bright nickel coating, it is necessary to carry out large-scale treatment. In the solution of bright nickel plating on stainless steel pipe, the brightener has developed rapidly and has many varieties. To sum up, the development of brighteners has experienced four generations. Instead of the original product, saccharin and butynediol can be plated with bright nickel with high flatness. Its application flourished in the s and s. It seems that due to the instability of butynediol in the nickel plating bath, short service life and rapid accumulation of organic impurities, the nickel bath needs to be treated frequently. Therefore, epoxy chloropropyl or epoxy is branched with butynediol to synthesize the second-generation nickel plating brightener, such as b brightener. The situation has improved. Be and retain alkynyl. Later, pyridinyl is polymerized to form the third-generation product, Faster light output, less amount of brightener and longer service life. Now it further uses various combinations of nickel plating brightener intermediates to form a new brightener, which has developed to the fourth generation of products. It has less use, faster light output speed and longer treatment cycle. According to the connection and rolling process, stainless steel pipes with deep plating capacity mainly include hot-rolled, hot-rolled and cold drawn (rolled) stainless steel pipes. According to the difference of metallographic structure of stainless steel, it mainly includes semi Ferritic and semi martensitic stainless steel pipe, martensitic stainless steel pipe austenitic stainless steel pipe, austenitic ferritic stainless steel pipe, etc.Hajjah, & mdash; high strength cutting tool steel, with slightly higher carbon content, can obtain higher yield strength after appropriate heat treatment, and the hardness can reach hrc. It is one of the hard stainless steels. A common application example is & ldquo; shaving blade & rdquo;. There are three common models: C and f (easy processing type).The main control load of the platform has high requirements for the shear bearing capacity of the guide leg of the offshore platform. In order to study the factors affecting the shear capacity of the jacket legs of the stainless steel pipe in pipe concrete-filled steel tubular offshore platform, concrete strength, void ratio and shear span ratio on the shear capacity of concrete-filled steel tubular in pipe. It is found that the shear strength of members increases with the decrease of void ratio and the increase of concrete strength; The larger the shear span ratio, the smaller the shear strength. Combined with the test, the empirical formula of shear capacity of concrete-filled steel tubular in pipe is proposed, which is analyzed and verified by ABAQUS finite element modeling software. The results show that the simulation is in good agreement with the test results. In order to study the axial compression performance of stainless steel tube concrete conduit leg and the axial compression performance of stainless steel concrete conduit leg, experiments are used to verify the correctness of the finite element model. The load displacement curves of specimens in groups were compared, and the effects of different void ratio, concrete strength, diameter thickness ratio and bone index on the axial compression performance of concrete-filled stainless steel tubular short columns under axial compression were analyzed. The results show that with the increase of concrete strength, but the ductility of specimens decreases; With the increase of void ratio and diameter thickness ratio, the bearing capacity of the specimen decreases; The bearing capacity of stainless steel tube concrete can be effectively improved by adding steel bone; Increasing the bone matching index of steel bone can improve the bearing capacity of the specimen. Based on the jacket offshore platform, it is proposed to replace the four hollow steel conduit legs of the original offshore platform with concrete-filled steel tube in stainless steel tube to form a new composite offshore platform with concrete-filled steel tube in stainless steel tube, so as to improve the ice resistance and disaster prevention ability of the offshore platform. The scale test on the offshore platform shows that the composite offshore platform of concrete filled steel tubular in stainless steel pipe (hereinafter referred to as the composite offshore platform) has better anti icing performance than the ordinary jacket offshore platform. Taking push as an example, the peak acceleration and displacement of the upper deck of the composite offshore platform of concrete filled steel tubular in stainless steel pipe are reduced by % and % respectively. The analysis of ABAQUS finite element and experimental simulation results shows that the error of the two results can be basically within %. Through the simulation analysis of the ultimate bearing capacity of the stainless steel tube in tube concrete-filled steel tubular composite platform and the original offshore platform, it can be seen that the stainless steel tube in tube concrete-filled steel tubular composite platform has stronger ultimate bearing capacity. Therefore, the composite offshore platform of concrete-filled steel tube in stainless steel tube is a good new type of jacket offshore platform. Axial compression tests were carried out on austenitic and duplex stainless steel tube concrete short columns. The ultimate load, longitudinal strain and circumferential strain of the short columns under axial compression were measured. The effects of steel tube wall thickness and concrete strength on the bearing performance of the short columns were investigated. Reference was made to the European Code for design of concrete filled steel tubes (Eurocode), American code (ACI -) and Japanese code (aij-cft) China's relevant regulations D --dlt- and CECS calculate the preparation of stainless steel pipe construction, prepare construction scheme and construction schedule scheme, and establish quality standards.And stainless steel are molybdenum containing stainless steels. The molybdenum content of stainless steel is slightly higher than that of stainless steel. Due to the molybdenum content in stainless steel, the overall performance of this steel is better than that of and stainless steel. Under high temperature conditions, when the concentration is lower than % and higher than %, stainless steel has a wide range of applications. Stainless steel also has good chloride corrosion resistance, so it is usually used in marine environment.

Welding, high frequency preheating plus three torch argon arc welding, high frequency preheating plus plasma argon arc welding. The progress of combined welding is very significant. As for the combined welding of steel pipe with high-frequency preheating, the weld quality is equivalent to the conventional argon arc welding and plasma welding, the welding operation is complex, and the whole welding is easy to complete automation. This combination is easy to connect with the existing high-frequency welding equipment, with low investment cost and good benefit.When selecting stainless steel water supply pipe, carefully observe whether the surface of the pipe is shiny damaged and crushed, and pay attention to whether the incision is neat. If these phenomena occur, they should be carefully considered.Model & mdash; High strength cutting tool steel, with slightly higher carbon content, can obtain higher yield strength after appropriate heat treatment, and the hardness can reach hrc. It belongs to hard stainless steel. A common application example is & ldquo; Shaving blade & rdquo;. There are three common models: C and f (easy to process).Customer firstWhen using this process, the correct included angle between the welding handle the following key points should be paid attention to: during the welding process, welding wire and weldment should be maintained. The ideal caster angle of the welding handle nozzle is & deg; & mdash; & deg;, change the welding speed change the included angle between the welding handle and weldment, etc. to change the molten pool temperature, so as to ensure Beautiful weld formation (uniform width, no concave, convex and other defects) During operation, the current shall be slightly larger than that of solid core welding wire, and the welding handle shall be slightly adjusted to accelerate the separation of molten iron and molten flux coating, so as to facilitate the observation of molten pool and penetration; when filling the welding wire, it shall be sent to places of molten pool and pressed inward slightly to ensure penetration and prevent concave; during welding, the welding wire shall be regularly sent and taken out, and the welding wire shall always be ensured Under the protection of argon to prevent the end of the welding wire from being oxidized and affect the welding quality; pay attention to the welding quality of the arc and arc stop, and the spot weld shall be polished to & deg; the slope shall be gentle, and pay attention to the defects such as arc pit and shrinkage hole during arc stop.When water-soluble paper is used to block the ventilation, due to the ventilation from the weld center, the ventilation pipe shall be pulled out quickly at the later sealing link, and the residual argon inside shall be used for protection, so as to quickly finish the bottom and seal the mouth.After that, the second widely used steel is mainly used in food industry, pharmaceutical industry and surgical equipment. Adding molybdenum makes it obtain a special corrosion-resistant structure. Because it has better chloride corrosion resistance than stainless steel pipe,Comitancillo316 cold rolled stainless steel plate, it is also used as & ldquo; marine steel & rdquo;. SS is usually used in nuclear fuel recovery devices. Grade stainless steel Steel pipes usually also meet this application level.

The back is blocked with blocking plate for ventilation protection; Only soluble paper or the combination of soluble paper and blocking plate is used for blocking ventilation protection; Use flux cored wire for backing TIG welding.install,There shall be a special storage rack. The storage rack shall be a wooden or painted carbon steel support or padded with rubber pad to isolate it from carbon steel and other metal materials. During storage, the storage position shall be convenient for lifting and absolutely isolated from other data storage areas. Protective measures shall be taken to avoid purification, collision with other components, purification and damage of iron metal.　　— After that, the second widely used steel is mainly used in food industry and surgical equipment. Molybdenum is added to obtain a special corrosion-resistant structure. Because it has better chloride corrosion resistance than it, it is also made & ldquo; Marine Steel & rdquo; To use. SS is usually used in nuclear fuel recovery units. Grade stainless steel generally meets this application grade. [] Model & mdash; Except that the risk of weld corrosion of the material is reduced due to the addition of titanium, other properties are similar.Assembly: the sealing ring shall be correctly installed in the U-groove of the pipe fitting, put the pipe into the socket of the pipe fitting and wait for crimping.Comitancillo, Series & mdash; martensitic precipitation hardening stainless steel pipe.Application field: tubular boiler for pipeline in harsh seabed environment product description: ultra (ultra) critical unit is the basis of modernization of power generation equipment and energy conservation and emission reduction. Among the important pressure parts of ultra (supercritical) boiler, superheater and reheater are the parts with high working temperature and bad working environment. Previously, all such materials used in China were imported from abroad, while only steel material manufacturers in the world have limited capacity. Such materials have a large gap, expensive import prices, which seriously affected the production of ultra supercritical boilers and the development of electric energy in China. At present, China's demand for utility boiler tubes is about tons,Comitancillo63 stainless steel pipe, and with the continuous improvement of ultra (supercritical) power generation technology,ComitancilloStainless steel 304 stainless steel, the demand is expanding. Several large domestic enterprises have invested a lot of human and financial resources in the R & D and production of such products, and have made considerable achievements. On the one hand, it has made its own contribution to the development of national electric power industry, but also brought considerable economic benefits to enterprises.The best way to improve the quality of stainless steel pipe fittings is to change the process from ingot to billet. Due to the improvement of continuous casting process, this has become a necessary means to improve product quality.