The motor is scrapped. Moreover, the installation and use of the pump is troublesome, and the application occasions are subject to many restrictions.　　 First remove the pump from the engine.FAO,　　 Check the winding of the motor: if the winding is damp or there are dust, sand and other attachments on the winding, which may reduce the insulation of the winding it should be removed immediately.　　After the submersible slurry pump leaves the factory, there is generally only outgoing cable,FAOSubmersible non clogging slurry pump, and the user needs to connect it separately during installation. If the connection is wrong, it will seriously affect the normal operation of the pump, so we should follow the correct steps to connect.Leova,　　 Next, you can place abrasive cloth on the glass or dry wood,FAOQJ submersible pump, and then grind the water seal of Boshan submersible slurry pump flat or turn it over for use. However, if the thrust rubber water seal is used, when　　 selection of pump head: generally, the pump head shall be determined by enlarging the margin of % - %.　　 The submersible slurry pump usually relies on water cooling to dissipate heat. If the motor leaks out of the water without water cooling, the motor temperature will rise,FAOWQ submersible pump parameters, so it is easy to burn out the motor.

　　The vertical sand pump is generally a submersible slurry pump. Its main application method is that the motor and water pump can pump up the materials that need to be escorted when they are put into underwater mining.　　There is no suction line. As the water storage tank is not deep enough and the suction pipe of the water pump is not deep enough, the inlet pipe of the water vortex is not deep enough. Water with a lot of gas. Destroy all normal water Self-priming pumps. To ensure sufficient depth of digestion and absorption of low watermark water. At that time, the depth was .~lm, and it was impossible to　　 After each use of the equipment, high-pressure water should be used to wash the pump and pipes. The washing can be stopped until the water has no impurities.safety requirements ,　　However, there is also a disadvantage of using the auxiliary impeller sealing system, that is, it takes some energy on the auxiliary impeller of the submersible slurry pump, which is generally about %. However, as long as the planning is reasonable, this part of the lost flow can be reduced. The slurry pump is mainly applicable to electric power, metallurgy and coal　　Generally speaking, the above two cases are the case that the slurry pump does not absorb water. The solutions are also introduced. I believe that people can deal with this problem in time. However, if the problem is serious, you must not adjust it at will. At this time, you should find a professional　　The pump should be divided into two aspects: electricity and machinery. As for machinery, you can compare the previous maintenance records. The second is electricity. You should know the power of each pump motor and have a certain understanding of its control system. Slurry pump with mechanical seal

　　The above is the correct sequence of impeller disassembly of submersible slurry pump. Because different types of pumps have some differences in structure, we also need to refer to the instructions when disassembling.Energy costs,　　 Next, the water seal, lock ring and other parts need to be installed.　　The answer to this question must be! Submersible sewage pump has attracted more and more attention because of its wide range of applications and strong sewage treatment capacity, but improper use and maintenance will lead to submersible sewage.　　 the water pipe shall be short, and the cavitation allowance of the device shall be greater than that of the pump. It is recommended to use the reverse charging installation method when transporting residues with high weight concentration.FAO,　　It should be /-/ between. When the packing is worn, the packing gland can be properly pressed. If it is worn too much, it should be replaced. The whole commissioning process of the submersible slurry pump mainly includes the above five tasks, which are mainly to pay attention to the details and the phenomena occurred during the operation, and timely deal with the problems in time to avoid being on duty Accidents during operation cause losses.　　 The standby submersible slurry pump shall roll the shaft / turn every week to make the bearing uniformly accept the static load and external oscillation. The building structure in the water pump room shall be reconstructed. Sound absorbing and isolating plates shall be installed around the wall and on the top of the machine room and fixed with light steel keel; The connecting holes between the machine room and other rooms are tightly blocked, the diving depth of the submersible slurry pump is not more than meters and the operation is reliable. Why not more than meters? This is the crucial technical point of the submersible slurry pump, not because the slurry pump has a problem because the current sealing technology in China is more than meters, but because