After the submersible slurry pump leaves the factory, there is generally only outgoing cable, and the user needs to connect it separately during installation. If the connection is wrong, it will seriously affect the normal operation of the pump, so we should follow the correct steps to connect.　　Some corrosive pastes containing crystals can also be transported. In the application range of slurry pump, about % are used in concentrators in the mining industry. Due to the poor working conditions of primary ore dressing,Gann tikwaHH slurry pump, the service life of slurry pump in this section is generally low. Of course, different minerals, abrasionGann tikwa,　　QW (WQ) submersible non blocking sewage pump needs to be equipped with a fully active water pump control cabinet under no exceptional conditions. Do not directly connect the power grid or use the knife switch to connect the power supply to ensure the normal operation of the electric pump.　　.Viransehir,　　 If the hot water within ℃ is recommended, the hot water pump must be used, and the external tap water shall be connected for cooling during operation, otherwise the motor will not be burned due to too high medium temperature.　　The seal cannot bear the water pressure at this depth. Once the water leaks, it will not affect the detection results. Therefore resulting in damage to the submersible slurry pump. The biggest difference between the submersible slurry pump and the horizontal slurry pump and the vertical slurry pump is that the motor of the submersible slurry pump and the shaft connected to the pump are integrated and sealed Closed.　　Submersible slurry pump Use ultrasonic method to detect whether there is cavitation in the submersible slurry pump. This method is often convenient for re detection. Even if there is some noise in the surrounding environment, many pumps often have better measurement results when in use.

　　The purpose is to avoid water leakage of the pump, but the water seal may be damaged due to faults after being used for a period of time. Let&#;s learn how to replace the water seal.　　Distance from the dynamic water level of the pool to the center of the water outlet of the pump base (m)　　Through the introduction, we learned that the submersible slurry pump can be used to transport slurry when it is used at ordinary times. The relationship between its special structure is very close, but in fact, it also needs to be used in a correct way when it is used at ordinary times. Only in this way canOnline consultation,　　What is the cause of pump overload.　　Water pump After understanding the cause of insufficient liquid supply, we can solve the problem: First, we need to check whether the liquid level of the circulating liquid storage tank needs to add media to it.　　The slurry pump of underground pump can also work normally.

　　To repair the equipment. Submersible slurry pump is a machine used to transport liquid. It can be divided into many types according to different transport media. Then, the equipment will be treated with corrosion-resistant and wear-resistant process. Only in this way can the equipment be improvedQuotation sheet,　　It is also necessary to clean the ventilation duct to avoid blockage.　　Several common specifications and models.　　 the water pipe shall be provided with a gate valve to regulate the pump working point. The valve shall be installed as close to the pump outlet as possible. The pump unit greater than meters shall be provided with a check valve at the pump outlet. In case of sudden shutdown, it is necessary to prevent damage to flow passage components caused by water hammer.Gann tikwa,Gann tikwaSewage pump diving,　　Let the medium containing some solid particles generate a certain flow rate, so that the equipment can drive the solid to flow when it is in use, so that the slurry can be transported. In terms of the principle of the submersible slurry pump, it is actually quite simple　　The pump can often be selected according to the specific requirements of lift, flow and liquid delivery. The flow range of the delivered liquid is - L / s, the pressure range is .- MPa, and the diesel engine speed range is - rpm. Features: water pump high automation and performance　　The whole packing body, including the packing gland,Gann tikwaPipeline pump, packing ring and packing, needs to be disassembled; Submersible slurry pump Disassemble the o-seal ring, balance disc and key on the shaft in turn, and then the discharge section includes the last stage guide vane