parts shall be dried with air compression or hot gas, or drying treatment or air drying can be selected.X-ray or ultrasonic testing shall be carried out for repair welding of alloy pipe, dead end welding of strip steel and circumferential seam. For the spiral welding of steel for the transportation of flammable general liquids,Joint stockHow many kilograms per meter of 100 welded pipe, yibai%sx ray or ultrasonic testing shall be carried out. For the spiral welding of alloy pipes for the transportation of water, wastewater, gas, heating steam and other general liquids, X-ray or ultrasonic testing sampling inspection (%) shall be carried out.Joint stock,Straight seam welding is adopted for larger diameter welded pipe, and spiral welding is mostly adopted for large diameter welded pipe; According to the top appearance of seamless steel pipe, it is divided into annular welded pipe and special-shaped (square, pitch, etc.); according to different materials and main purposes, it is divided into mining anti liquid transportation welded steel pipe, hot-dip galvanized welded steel pipe for bottom pressure liquid transportation, continuous conveyor idler electric welded steel pipe, etc. it is arranged from small to large according to diameter * wall thickness according to the specification, model and dimension table in the current standard.The specification of pass design I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is. The types of I-beam include hot-rolled ordinary I-beam, light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~, expressed as No. ~ No., and the inclination of inner wall of leg is : The pass system of rolled I-beam includes direct pass system, cross pass system and mixed pass system. In addition, I-beam can also adopt special rolling method.Cape-Pitt,As shown in the name, I-beam is an I-shaped section steel. The inner surface of the upper and lower flanges has an inclination, generally :, which makes the outer flange thin and the inner flange thick. Therefore, the section characteristics of I-beam in the two main planes are very different, and it is difficult to give full play to the strength characteristics in application. Although the thickened I-beam has also appeared in the I-beam market, the structure of the I-beam has determined its torsional performance.The general alloy pipe with improved performance is variable and has high application value. The alloy pipe contains more Cr and is heat resistant Low temperature resistance Corrosion resistance. There is no aluminum alloy in plain carbon seamless steel pipe, and the alloy pipe is used in crude oil Aerospace Chemical plant Power engineering heating furnace. Because the physical properties of alloy tubes are easy to change and adjust.Requirements of alloy tubes for low and medium pressure boilers

Alloy pipe is a very important way and type of seamless steel pipe. Its use is relatively common. It is widely used in various engineering projects, house construction and building decoration. Its fracture will always be found in the production, many stages of production and processing are not done well. Another is that the seasoning is not enough and the proportion of chemical molecules is wrong. There are all reasons. For the surface mesh of the height difference plate That is when the height difference is ≤ mm, the surface mesh can be bent and installed; when the height difference plate is more than mm the surface mesh should be disconnected at the place with height difference and put into the beam respectively. The anchorage length of the reinforcement is required for the reinforcement to extend into the beam.I-beam, also known as universal beam, is a long strip of steel with I-shaped section. I-beam is divided into ordinary I-beam and light I-beam. It is a section steel with I-type section shape.Quality improvement,Key technical characteristics of alloy pipe:GB No. I-beam is in height, in leg width and in waist thickness.Heating surface pipes, reheaters, pipes for petrochemical industry, etc. for high-pressure boilers (working pressure is generally above MPa and working temperature is between ℃ ~ ℃)

Aiming at the connective tissue and texture produced in stainless steel plate Position and other crystal defects are generally removed by heat treatment processes such as quenching or quenching. The effect of quenching is to optimize the crystal, eliminate structural defects, reduce strength, improve plastic deformation, and also conducive to cold drawing. In the production and manufacture of cold drawn alloy pipe, quenching machinery and equipment cannot be lacked. Therefore, the formulation of appropriate annealing process is a necessary condition to ensure that the alloy pipe mechanism meets the standard and the commodity does not crack. If the manufacturer in order to better one sidedness, reduce the product cost and reduce the quenching process, it will eventually lead to bad harm to the product quality.Information recommendation,Whether I-section steel is ordinary or light, because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different, so it can only be directly used for members bent in the plane of their web or form lattice stressed members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application. I-beam is widely used in buildings or other metal structures.In addition, galvanized steel is more expensive than ordinary steel pipes, so installing them requires a lot of financial costs.I-beam is mainly divided into ordinary I-beam, light I-beam and wide flange I-beam. According to the height ratio of flange to web, it is divided into wide, medium and narrow flange I-beams. The specifications of the first two are - that is, the corresponding height is -. At the same height, the light I-beam has narrow flange, thin web and light weight. Wide flange I-beam, also known as H-beam, is characterized by two parallel legs and no inclination on the inner side of the legs. It belongs to economic section steel and is rolled on four high universal mill, so it is also called 'universal I-beam'. Ordinary I-beam and light I-beam have formed national standards.Joint stockI-beam,Joint stockInconel 600 alloy pipe, whether ordinary or light, can only be directly used for bending members or lattice members on its Web because of its large and narrow section size and large moment of inertia difference between the two main axes on the section. It is not suitable for axial compression members and flexural members perpendicular to the web plane, so its application range is very limited. I-beams are widely used in buildings and other metal structures. Small longitudinal crackBecause all parts of I-beam are arranged at right angles, I-beam has the advantages of strong bending resistance,Joint stockCold drawn welded pipe manufacturer, simple construction, cost saving and light structural weight in all directions, and has been widely used. The inner and outer sides of the flange of the I-beam are parallel or close to parallel, and the end of the flange is at a right angle, so it is named parallel flange I-beam. The web thickness of I-beam is smaller than that of ordinary I-beam with the same height of web, and the flange width is larger than that of ordinary I-beam with the same height of web, so it is also named wide edge I-beam.