The lifting platform is a multifunctional heavy loading and unloading mechanical equipment, which can be divided into fixed and mobile, guide rail and curved arm types. Fixed types include scissor elevators, chain elevators, loading and unloading platforms, and attached electric construction platforms.Vehicle mounted lifting platform is widely used for high-altitude operations in hotels, buildings, airports, sports venues, workshops, warehouses, and other places; It can also be used as temporary high-altitude lighting, advertising, etc.Kenneth,The size of the oil cylinder should be minimized as much as possible while meeting the design requirements. The smaller the diameter of the oil cylinder, the faster the lifting speed.Voltage too low: Measure the starter voltage, with an allowable fluctuation range of± %.Ikhtiman,Remove the hydraulic oil tank filler cap, filter cover, inspection hole, hydraulic oil pipe and other parts to avoid dust when removing the system oil pipe. Clean the disassembled parts before opening them. When disassembling the hydraulic oil tank filler cap, first remove the soil around the tank cap, loosen the tank cap, open the tank cap.Load bearing capacity: The lifting platform is placed on a horizontal support surface, and the workbench is evenly loaded to % of the maximum load capacity. After lifting times, each load-bearing component must not have deformation or cracks. There is air in front of the pilot valve of the elevator overflow valve noise overflow valve. The damping hole on the main valve core of the overflow valve is blocked by oil dirt, and the pilot valve and valve seat are matched without spring deformation or incorrect installation. The remote control port has excessive oil flow, low or high hydraulic oil viscosity, and resonance occurs with components in the circuit. Troubleshooting: Strengthen sealing, repeatedly adjust the pressure, exhaust and clean the valve body several times, Make the damping hole unobstructed, repair or replace the spring, reduce the flow of the remote control port, replace the oil, and other components. The pressure setting of other components should not be similar to the pressure setting of the relief valve. . The noise of the elevator pipeline is usually caused by excessive dead bends or loose fixed sleeves in the hydraulic pipeline.

Solution: Check if the performance of the legs is good, even if the butter is polished to increase its properties.Usage and instructions for steel wire ropes in elevators: The steel wire ropes of the steel wire ropes require very high strength, usually made of high-quality carbon steel with a carbon content of .% -.%. They are widely used as transmission components in elevators. Due to its large load-bearing capacity, light weight, smooth operation no noise, suitable for high-speed transmission, high strength, strong overload capacity, and reliable operation, it has become a commonly used rope for hydraulic elevators.Reason: The lowering valve is not tightly closed. Cleaning method: Check if the lowering valve is powered on. If there is no power supply, clear the malfunction of the lowering valve itself or replace the lowering valve. It is necessary to keep the valve of the lowering valve clean and flexible.Excellent service,The characteristics of the platform include reliable hydraulic system, simple operation large load-bearing capacity, and rear hinge support.The hydraulic pump produces noise. When the hydraulic elevator rises, the hydraulic pump runs at high speed. If there is a problem with the gears or bearings of the hydraulic pump which causes periodic changes in the hydraulic system pressure,KennethIndoor hydraulic lifting platform car, it will also cause resonance in the hydraulic system and generate noise.Hydraulic elevator manufacturers remind us that the basic principle of the hydraulic elevator speed control circuit is that the system often needs to adjust the movement speed of the hydraulic cylinder and hydraulic motor to adapt to the working cycle needs of the main machine. The speed of hydraulic cylinders and hydraulic motors depends on the displacement and input flow rate. It can be seen that changing the flow rate or displacement can affect the speed of the cylinder and motor.

The hydraulic oil used in the system has the same brand, and the oil temperature is between ~ ℃. Use a large flow rate to remove impurities from the system as much as possible. The hydraulic system needs to be cleaned repeatedly three times or more, and after each cleaning, the system should be drained while the oil is hot. After cleaning, clean the filter and add new oil after using a new filter element.Quality recommendation,After long-term use of the automatic lifting platform equipment, it is inevitable that some malfunctions will occur. In order not to affect work, due to overload, insufficient power supply, and a small cross-sectional area of the power supply cable, the starting voltage drop is too large and the price of the cargo elevator is reduced.What are the benefits of hydraulic cargo elevators compared to traditional elevator cargo transportation?The use of cleaning oil and the brand used in the systemKenneth, conduct maintenance, cleaning,KennethHydraulic lifting platform, and replace the cleaning hydraulic oil to clean.When encountering signs of overheating in the electric motor it is necessary to park the car in a timely manner,KennethMobile elevator hydraulic lifting platform, clean the problem, and continue running. The motor bearings should be smooth and outstanding.The classification of lifting platforms is as follows: they are divided into mobile lifting platforms, automatic lifting platforms, hydraulic lifting platforms, folding arm lifting platforms, and sleeve type lifting platforms according to their different modes of movement.