The advantage of empty bending is that it can bend the side length when the real bending cannot be carried out, such as synchronous bending and finishing of the upper side and side of qb square tube. Empty bend can also bend R & amp; amp; lt; .T without fracture of pipe wall.Put the pig iron for steelmaking into the steelmaking furnace according to the specified process to obtain steel. The products of steel include ingots, continuous casting billets and various steel castings made of straight square tubes. Generally speaking, steel refers to the steel rolled into various square tubes. Square tube steel belongs to ferrous metal, but steel is not completely equal to ferrous metal.Straseni,The inner and outer walls of the pipe shall retain the original surface without any processing.The surface of fake and inferior square tubes is easy to produce scabs. There are two reasons: the material of fake and inferior square tubes is uneven and there are many impurities. The guide equipment of fake and shoddy material manufacturers is simple and easy to stick to steel. These impurities are easy to scar after biting the roll.Kronov,Improve the positioning and pre bending steps if necessary, to ensure that the web hunting problem does not occur when pressing parts. Change the shape of the surface pressure of the material to ensure the quality of the parts and avoid the non movement of the surface shape of the roll gap, resulting in uneven walking feeding.The disadvantage of empty bending is that when the upper side and side are synchronously empty bending,Straseni20 hot dip galvanized square pipe, the forming force is easy to exceed the critical point due to the pressure generated by the upper roll and the lower roll at the same time, resulting in edge instability and concave, and will also affect the stable operation and forming quality of the unit. This is also the different characteristics of qb square tube and round tube empty bending. The concept of square tube: square tube is the pressure processing of ingot, billet or square tube Make materials of all shapes, sizes and properties we need.Generally chemical and electrolytic methods are used

Section shape classification square tubes are classified according to section shape: simple section square tubes & mdash& mdash; Square tube, rectangular tube and complex section square tube & mdash& mdash; Surface treatment classification of flower shaped square pipe, open square pipe, corrugated square pipe and special-shaped square pipe square pipe is divided into hot-dip galvanized square pipe, electro galvanized square pipe, oil coated square pipe and pickling square pipe according to surface treatment. Square pipe is classified according to purpose & mdash& mdash; Square tubes for decoration, machine tools and equipment, machinery industry, chemical industry steel structure, shipbuilding, automobile, steel beam and column and special purpose are classified by wall thickness & mdash& mdash; Super square tube, square tube and thin-walled square tube plasticity refers to the ability of metal materials to produce plastic deformation (deformation) without deformation under load.The square tube is formed by external control or internal control roller.Structural stainless steel square pipe (gbt-) is a hot-rolled (extruded, expanded) and cold drawn (rolled) square pipe made of stainless steel for corrosion-resistant pipes, structural parts and parts widely used in chemical, petroleum, light textile, food,If the re inspection results are unqualified (including the items whose preliminary inspection results are unqualified and re inspection is not allowed) the supplier can submit them for acceptance one by one; Or re conduct heat treatment (the number of RE heat treatment shall not exceed times), and propose acceptance with a new batch.Plasticity QB square plasticity refers to the ability of metal materials to produce plastic deformation (deformation) without deformation under load.When the vehicle is replaced with seamless square tube blank, so as to ensure the quality of parts and avoid wrinkles.

Square tubes have different functions and different characteristics. Square tubes of various specifications, square rectangular tubes, seamless square tubes, galvanized square tubes and galvanized tubes are welcome to waste merchants, industries, enterprises and power departments to visit and negotiate! Oxidation will also occur on the surface of square tubes after long-term use. What should we do if oxidation occurs? Let me give you a detailed introduction on how to remove square tubes Oxide scale.Where can I find it?,Due to the increase of square tube production, good cold deformation plasticity and weldability; In addition, but it has quite high strength and wear resistance, especially when water quenching; However,StraseniGalvanized square pipe, this steel has great resistance to white spots, temper brittleness and overheating during heat treatment.In this period, the technology of continuous rolling pipe was not mature.Straseni,In the square tube production process of welding before forming, the forming is mainly completed by the sizing frame. The sizing machine is generally a two high mill, including horizontal frame and vertical roll frame. At present, there are mainly two kinds of square pipe pass design: one is the horizontal frame is designed according to the box hole, the frame is an elliptical hole, and the other frames are approximately rectangular holes. The pass section is composed of circular arc. Professional projects include: square pipe, square pipe, seamless square pipe, galvanized square pipe, galvanized pipe and other related businesses. Please welcome merchants who want to have this business. And the arc radius increases frame by frame, The fillet radius of the joint between the side wall and the bottom of all pass patterns is equal to the fillet radius of the finished section. The total elongation coefficient of the square tube is about , which is mainly distributed on the flat roller. The deformation of the vertical roller is very small, and its function is to press down the short side of the square tube. With this design, the calculation is complex and the calculation value is not accurate enough. It is necessary to constantly correct the pass circumference.Viewing color: the color of the cold galvanized square tube is yellowish green, cyan white or slightly colored at a fixed angle with the sun. The color of hot-dip galvanized square pipe is silver white at a fixed angle with the sun.Product description of square tube square tube is a light thin-walled steel tube with hollow square section, also known as steel cold-formed profile. It is a section steel with square section shape and size, which is made of Q hot-rolled or cold-rolled strip or coil as the base material,StraseniQ235B square tube, cold bending and high-frequency welding. In addition to wall thickness thickening, the corner size and edge flatness of hot-rolled special square pipe reach or even exceed the level of resistance welding cold-formed square pipe. Good comprehensive mechanical properties, weldability, cold and hot workability and corrosion resistance, and good low temperature toughness.