Ship carbon steel square pipe (gb-) is a carbon steel square pipe for ship class I pressure pipe system, class II pressure pipe system, boiler and superheater. It is a long-term business square pipe, square pipe, seamless square pipe, galvanized square pipe and galvanized pipe. Welcome to consult. The working temperature of carbon steel square pipe wall shall not exceed ℃, and the working temperature of alloy steel square pipe wall shall exceed ℃.Stage ( & mdash; )Pelepe,Square tubes can be degreased with organic solvents (vinyl chloride, vinyl chloride, carbon chloride, industrial solvents, benzene,PelepeGalvanized square pipe 100, acetone, etc.), concentrated or alkaline solution. Industrial vinyl chloride is suitable for degreasing metal parts; Industrial chlorinated carbon is suitable for degreasing ferrous metal and non-metallic parts; Vinyl chloride is suitable for degreasing metal parts and non-ferrous metal parts; The industrial concentration shall not be less than %, which is suitable for manual scrubbing of the inner surface of the container with low degreasing requirements; % concentrated, suitable for degreasing some pipe fittings and porcelain rings of concentrated device.In this period, the technology of continuous rolling pipe was not mature.Atakpame,With the progress of the times and the faster and faster economic development, the places where large-diameter seamless square tubes are used are becoming more and more popularImprove the positioning and pre bending steps if necessary, to ensure that the web hunting problem does not occur when pressing parts. Change the shape of the surface pressure of the material to ensure the quality of the parts and avoid the non movement of the surface shape of the roll gap, resulting in uneven walking feeding.Principle of cold drawing strengthening: the lattice defects of steel increase during plastic deformation, and the serious distortion of defect lattice will hinder the progress and slip of lattice, so the yield point of steel increases and the plasticity and toughness decrease. Due to the internal stress in plastic deformation, the modulus of steel decreases. The cold drawn reinforcement is stored at room temperature for ~ d or heated to ~ ℃ and maintained for a fixed time. This process is called aging treatment.

The difference between square pipe and seamless steel pipe the main feature of seamless steel pipe is no welding joint and can withstand large pressure. The product can be very rough as cast or cold drawn parts.Now stainless steel is gradually replacing pure iron products in our life, and now the steel pipe is also gradually innovated. Now the qb square pipe is a typical representative. However, the above small series are not the focus. Today, the focus is on the analytical process of qb square tube sizing rolling.Square tube is an essential material for the construction and Realization of industrialization. It is widely used and has a wide variety. According to different section shapes, square tube is generally divided into sections, plates, pipes and metal products. In order to facilitate the production,PelepeQ235 galvanized rectangular pipe, ordering and supply of square tube and do a good job in operation and management, it is also divided into heavy rail, light rail, large section steel, small section steel and square tube cold bending Section steel, high-quality section steel, medium and thick steel plate, sheet steel, electrical silicon steel sheet, strip steel, seamless steel pipe, welded steel pipe, etc.new productThe disadvantage of empty bending is that during synchronous empty bending at the upper and side, due to the pressure generated by the upper roll and the lower roll at the same time, the forming force is easy to exceed the critical point. All kinds of square tubes, square rectangular tubes, seamless square tubes, galvanized square tubes and galvanized tubes have formal qualifications. Welcome to telephone inquiry and sincerely invite cooperation! It will cause edge instability and concave, and the tensile effect will shorten the longitudinal length of the bending line; The metal at the real bend will become thinner due to stretching.Engaged in square tube, square rectangular tube, seamless square tube, galvanized square tube, galvanized tube, old brand, price advantage and quality guarantee! However, the Demander shall cut off the interface pipe when using it. The weight of short length and non fixed length products shall not exceed % of the total delivery. For qb square pipe with theoretical weight greater than kgm it shall not exceed % of the total delivery. The bending degree of qb square pipe shall not be greater than mm per meter, qbqb with standard number of gbt-. Representative materials: QA, etc. It is mainly used for conveying water, gas, air, oil and heating hot water or steam, and its purpose is limited to general low pressure fluid.

Spraying (throwing) derusting spraying (throwing) derusting is that the high-power motor drives the spraying (throwing) blade to rotate at high speed, so that the steel sand, steel shot, iron wire section, minerals and other abrasives can be sprayed (thrown) on the surface of the square tube under the action of centrifugal force, which can not only completely remove rust oxides and dirt, but also the square tube under the violent impact and force of abrasives, It can also achieve the required uniform roughness.Management Department,Square tube plays an important role in the rapid economic development. The functions of square tube are different, and its characteristics are also different. Square tube has strict standards. There are many welding processes and advantages of square tube. Let me show you the welding process and advantages of lower tube.After isothermal quenching, qqb square tube will have excellent rolling fatigue characteristics and corrosion resistance. Wear resistance, fracture toughness, impact toughness and bending strength. Therefore, in the subsequent production and application, qqb square tube will be used as the material of rolling mill flap ball screw. The qqb square tube of case hardening steel also has the surface compressive stress characteristics obtained by heat treatment, and its application range is expected to be improved and expanded.The pressurization size and time are the key to the success or failure of welding. If the square tube synthetic material is not pressurized, a large number of pores will be caused due to the pores of the material itself and the gas generated in the reaction. It is not allowed to leave the reactants in the weld, so it must be densified, usually pressurized during the reaction.Pelepe,The pressurization size and time are the key to the success or failure of welding. If the square tube synthetic material is not pressurized, a large number of pores will be caused due to the pores of the material itself and the gas generated in the reaction. It is not allowed to leave the reactants in the weld, so it must be densified, usually pressurized during the reaction.Large diameter qb square tube production standard classification square tube is divided according to production standard: national standard square tube, Japanese standard square tube, British standard square tube, American standard square tube, European standard square tube and non-standard square tube.Fake and shoddy square tubes are easy to scratch, because the equipment of fake and shoddy material manufacturers is simple and easy to produce burrs and scratch the surface of square tubes. Deep scratches reduce the strength of square tubes.