For improper stamping direction, and when the high-quality requirements of components require the re development of molds, the direction shall be adjusted to seamless square tubes. The square tube manufacturer introduces the forming, bending and bending of square tubes. As the name suggests, the bending is compacted, and the inner and outer rollers are double with the inner and outer walls of tube billets during actual bending Compact towards the.C. special performance steel: (a) stainless and acid resistant steel; (b) Heat resistant steel; (c) Electric heating alloy steel; (d) Electrical steel; (e) High manganese wear resistant steel.Vinekar ,When the square tube is covered, the surface of the square tube shall be ventilated to avoid the collection of water vapor on the surface due to difficult volatilization.According to metallographic classification, the annealed state of square tube: A. hypoeutectoid steel (ferrite + pearlite); b. Eutectoid steel (pearlite); c. Steel precipitation through a common square tube (pearlite + cementite); d. Ledeburite steel (pearlite + cementite).Lojo, special shaped square pipe is the general name of square pipes with other cross-section shapes except circular pipe. According to the different cross-section shape and size of steel pipe, it can be divided into special-shaped square pipe with equal wall thickness (code D), special-shaped square pipe with unequal wall thickness (code BD) and special-shaped seamless steel pipe with variable diameter (code D) These special-shaped large-diameter qb square tubes are widely used in various structural parts, tools and mechanical parts. Compared with circular tubes, special-shaped tubes generally have large moment of inertia and section modulus, and have large bending and torsion resistance, which can greatly reduce the structural weight and save steel. Square tubes are an indispensable part of construction workGenerally, chemical and electrolytic pickling are used for pickling treatment. Only chemical pickling is used for pipelines, which can remove oxide scale, rust and old coatings. Professional square tubes, rectangular tubes, galvanized square tubes and galvanized tubes are safe,Vinekar Lined plastic hot dip galvanized steel pipe, environmentally friendly and economical! The products are exported to foreign countries and are deeply trusted. Sometimes they can be used as reprocessing after sand blasting and rust removal. Although chemical cleaning can make the surface reach a certain cleanliness and roughness,Vinekar Manufacturer of galvanized square pipe, its anchor lines are shallow and easy to pollute the environment.Hot dip galvanized square pipe is widely used, mainly in curtain wall, solar power generation support, construction, machinery and steel structure engineering, especially in curtain wall, machinery and construction. The effect of cold galvanized square tube is far from that of hot galvanized square tube; How to distinguish hot galvanized square pipe from cold galvanized square pipe?

After cold drawing and aging treatment, the yield point is improved, the tensile ultimate strength is also increased, the modulus can be basically restored. According to this principle, cold drawing or cold drawing of reinforcement or low carbon steel wire rod is often carried out on site or prefabricated component factory, so as to improve yield strength and save steel.Square tube flattening test is a kind of test to check the deformation performance of metal tubes (seamless square tubes and rectangular tubes) flattened to the specified size and show their defects. Relevant flattening tests shall be carried out in accordance with relevant provisions of test standards. Requirements for samples samples can be taken from metal pipes with qualified appearance. Generally, sawing is adopted. The inner and outer walls of the pipe shall retain the original surface without any processing. Sample length L & asymp; D (D is the outer diameter of the pipe). When the outer diameter is large, the length l shall not exceed mm. When the outer diameter is less than mm l = mm. When cutting the sample, the surface of the sample shall not be damaged and the performance of the metal shall not be changed due to heating or cold processing. The edge of the section shall be flattened. The flattening test is a test to check the deformation performance of the metal pipe (seamless square pipe and rectangular pipe) flattened to the specified size and show its defects. Relevant flattening tests shall be carried out in accordance with relevant provisions of test standards.In the square tube production process of welding before forming, the forming is mainly completed by the sizing frame. The sizing machine is generally a two high mill, including horizontal frame and vertical roll frame. At present, there are mainly two kinds of square pipe pass design: one is the horizontal frame is designed according to the box hole, the frame is an elliptical hole, and the other frames are approximately rectangular holes. The pass section is composed of circular arc. Professional projects include: square pipe, square pipe, seamless square pipe, galvanized square pipe, galvanized pipe and other related businesses. Please welcome merchants who want to have this business. And the arc radius increases frame by frame, The fillet radius of the joint between the side wall and the bottom of all pass patterns is equal to the fillet radius of the finished section. The total elongation coefficient of the square tube is about , which is mainly distributed on the flat roller. The deformation of the vertical roller is very small, and its function is to press down the short side of the square tube. With this design, the calculation is complex and the calculation value is not accurate enough. It is necessary to constantly correct the pass circumference.offerThe disadvantage of empty bending is that when the upper side and side are synchronously empty bending, the forming force is easy to exceed the critical point due to the pressure generated by the upper roll and the lower roll at the same time, resulting in edge instability and concave, and will also affect the stable operation and forming quality of the unit. This is also the different characteristics of qb square tube and round tube empty bending. The concept of square tube: square tube is the pressure processing of ingot, billet or square tube Make materials of all shapes, sizes and properties we need.C. special performance steel: (a) stainless and acid resistant steel; (b) Heat resistant steel; (c) Electric heating alloy steel; (d) Electrical steel; (e) High manganese wear resistant steel.A. square tube structural steel: (a) high quality carbon structural steel; (b) Alloy structural steel; (c) Spring steel; (d) Easy cutting steel; (e) Bearing steel; (f) High quality structural steel for specific purposes.

If there is only a single plane weld the step-by-step back welding shall be adopted from the middle, the arc of the section weld shall be terminated at the section arc.superior quality that is,Pull square tube:The surface compressive stress characteristics of the square tube will be obtained after isothermal quenching.Square tube has a wide range of application fields. Its main field is the construction industry,Vinekar Galvanized pipe fittings manufacturer, which promotes the development of economic construction. Because the production process of square tube hole is different, the production design of square tube hole is also different. Next, I will introduce in detail the types of tube hole design below.Vinekar ,The advantage of empty bending is that it can bend the side length when the real bending cannot be carried out, such as synchronous bending and finishing of the upper side and side of qb square tube. Empty bending can also bend the inner corner of r.t without breaking the tube wall.After cold drawing and aging treatment, the tensile ultimate strength is also increased, and the plasticity continues to decrease. Due to the reduction of internal stress during aging, the modulus can be basically restored. According to this principle, cold drawing or cold drawing of reinforcement or low carbon steel wire rod is often carried out on site or prefabricated component factory, so as to improve yield strength and save steel.The advantage of empty bending is that it can bend the side length when the real bending cannot be carried out, such as synchronous bending and finishing of the upper side and side of qb square tube. Empty bending can also bend the inner corner of r.t without breaking the tube wall.