High density may not be obtained by simple pressurization, and insulation shall be carried out at the same time.Square tubes for petroleum cracking (gb-) are furnace tubes, heat exchangers and pipeline square tubes suitable for petroleum refineries.Cochani,The general delivery length of qb square pipe is mm-mm, mostly mm and mm. Qb square tube is allowed to deliver short and non fixed length products not less than mm,CochaniPrice list of galvanized pipe, or in the form of interface tube but the Demander shall cut off the interface tube when using it. The weight of short length and non fixed length products shall not exceed % of the total delivery. For qb square tube with theoretical weight greater than kgm,CochaniGalvanized steel round pipe, it shall not exceed % of the total delivery. The bending degree of qb square tube shall not be greater than mm per meter, and the total bending degree shall not be greater than .% of the total length. The square tube is classified according to the production process: hot rolled seamless square tube, cold drawn seamless square tube, seamless square tube and square tube.A. square tube structural steel: (a) high quality carbon structural steel; (b) Alloy structural steel; (c) Spring steel; (d) Easy cutting steel; (e) Bearing steel; (f) High quality structural steel for specific purposes.Kampong Masjid Tanah,Square tube is a very good steel in economic construction. There are many kinds and principles of cold drawing. You may still have a lot of insufficient understanding of the cold drawing principle of each other's pipe. Next, I'll lead you to learn its cold drawing principle.Steel for construction and engineering according to the classification of use without phase transformation or partial phase transformation of square tube: A. ordinary carbon structural steel; b. Low alloy structural steel; c. Steel reinforcement.Alloy steel: A. low alloy steel (total alloy element content & le; %); b. Medium alloy steel (total alloy element content > ~ %); c. High alloy steel (total alloy element content > %).

Square pipe welding is suitable for surface treatment of materials. Square pipe welding can be used for ceramic ceramic, we need to deal with them in time. What are the reasons for the rusting and corrosion of square tubes? Let's introduce them to you next.Viewing color: the color of the cold galvanized square tube is yellowish green, cyan white or slightly colored at a fixed angle with the sun. The color of hot-dip galvanized square pipe is silver white at a fixed angle with the sun.Quality risk,Stage ( & mdash; )Viewing color: the color of the cold galvanized square tube is yellowish green, cyan white or slightly colored at a fixed angle with the sun. The color of hot-dip galvanized square pipe is silver white at a fixed angle with the sun.It should be noted that the position of the disc from the calibration line can be adjusted according to the reinforcement diameter, and R and R can be equal or different.

Viewing color: the color of the cold galvanized square tube is yellowish green, cyan white or slightly colored at a fixed angle with the sun. The color of hot-dip galvanized square pipe is silver white at a fixed angle with the sun.Scheme customization,Special performance steel: A. stainless and acid resistant steel; b. Heat resistant steel: including oxidation resistant steel heat strength steel and air valve steel; c. Electric heating alloy steel; d. Wear resistant steel; e. Low temperature steel; f. Electrical steel.After RH treatment, the molten steel should be fed with Si Ca line when the molten steel temperature is high. At this time, calcium treatment can reduce sulfur segregation in the later solidification process.According to smelting classification and furnace type, A. open hearth steel: (a) acid open hearth steel; (b) Alkaline open hearth steel.Cochani,Solution treatment and nondestructive testing sand rolling treatment and sand blasting treatment many manufacturers in the market do not do solution treatment and % penetration nondestructive testing, and many of them use sand blasting instead of sand rolling. After these steps are omitted the cost is greatly reduced.Square tube heating process square tube calculates the chip thickness of workpiece. After each regrinding, the service life of the saw blade. Regrinding times of the saw blade. When the saw blade is replaced, the main drive AC motor spindle rotates stepless speed change AC motor feed capacity stepless speed change feed fast return to a constant value center system brush device hydraulic saw cutting system system system represents the quality RA flatness, large burr height cutting Chip length tolerance dimension: width and length . ~ .mm ~ m ~ ~ min kW ~ rpm ( kw ~ mmmin mmmin .kw .kw & times; kW S & mu; m . mm & plusmn; mm about mm about mm about mm high. The total weight of each billet square tube is seconds (including, pipe blank cutting, saw blade return, opening device, pipe blank discharge,Cochani45 galvanized square pipe, but excluding pipe blank transportation time). The large production capacity of the three saws is T / A. the pipe blank saw has a special reversing device (hydraulic servo device) to reduce vibration and improve the service life of the saw (only during feeding). The sawing machine has two devices distributed at the inlet and outlet (the input area is supported by roller table to ensure the bending of billet) The inlet end after sawing. Open it to ensure that the saw blade does not contact the blank when it returns. & mdash; feed saw gear & mdash; saw gear vibration reduction, which is composed of a fixed gear vibration reduction, as a movable vibration reduction to avoid the axial of the saw blade. & mdash; brush and sweep device & mdash; a driving brush and sweep device is installed at the bottom of the saw blade to clean the iron filings on the teeth and will not affect the service life of the saw blade. &Mdash; saw blade. In order to improve the service life of the saw blade, a small amount of high load agent container is atomized by air and poured on the saw blade without residue. & mdash; saw blade cooling device. A special nozzle is used to spray cold air at - oC on the saw blade. The cut-off blank is transferred to the buffer chain in front of the loader after passing through the outlet roller table and weighing device (Note: # before sawing, there is a feeding bench for single size billets that need to be cut, and after weighing, there is a feeding bench for returned billets). The buffer transfer chain transports the billets to the lower roller table of the loader. The billets are turned over from the chain to the roller table by the turnover hook. The weighed qualified billets are loaded into the annular furnace by the loader, such as synchronous bending and finishing of the upper side and side of qb square tube. Empty bend can also bend R & amp; amp; lt; .T without fracture of pipe wall.