put the pipe into the socket of the pipe fitting and wait for crimping.Duplex stainless steel product description: This stainless steel has good corrosion resistance in urea carbamate solution and high stress corrosion cracking resistance in chloride environment. At the same time

Assembly: the sealing ring shall be correctly installed in the U-groove of the pipe fitting, the duplex stainless steel has excellent mechanical properties and can be used in plant construction with high safety requirements.Berlin,If you want to choose a high-quality stainless steel pipe water supply pipe, you should first see whether its material is superior. Stainless steel is a material with strong corrosion resistance and high sanitation and cleanliness. Not only the outer wall is very beautiful, but also very smooth. There will be obvious differences in material first in terms of incision and whether the stainless steel pipe water supply pipe is good or bad.The back side is not protected by argon, and the flux coated welding wire (self protective flux cored welding wire) + TIG process is adopted. In the s, the backing welding wire has been developed. Recently, China has also developed the stainless steel backing welding wire (i.e. flux coated welding wire, such as tgftgftgftgf, etc.) It has been applied to the actual construction and achieved good results. We have successfully applied it in the capacity expansion and reconstruction project of Urumqi Petrochemical.Patos-Fshat,Water preparation, storage, transportation, purification, regeneration, and there is no & alpha during heating and cooling=& amp; amp; gt;& gamma; The transformation cannot be strengthened by heat treatment. Strong oxidation resistance. At the same time and the carbon content is less than .%. Other alloying elements are sometimes added. The metallographic structure is mainly ferrite, it also has good hot workability and certain cold workability. Ferritic stainless steel is mainly used to make components with high corrosion resistance and low strength requirements. It is widely used in manufacturing equipment such as production, nitrogen fertilizer and chemical pipelines.At present, stainless steel backing is divided into two processes: back argon filling and non argon filling. Back argon filling protection can be divided into solid wire + TIG process and solid wire + TIG + water-soluble paper process; The back non argon filling protection is also divided into flux cored wire backing welding and welding rod (flux coated wire) backing TIG welding.

Stainless steel pipe is durable and has been recognized by the engineering community, and relevant parties are starting from reducing the wall thickness and lowering the grid, so as to facilitate further development. In particular, the price of stainless steel pipe is not high, so the supporting connection, the reliability and price of pipe fittings are the main factors determining its development. Domestic developers have independently developed connection technology and pipe fittings in Sichuan, Guangdong, Zhejiang, Jiangsu and other places, which is a promising pipe. The Ministry of construction and relevant departments also attach great importance to this new type of pipe. According to China technology market management promotion center and gksz [] No. document on Application & ldquo; High diameter to wall ratio and high precision stainless steel medium and high pressure water supply pipes and supporting fittings and special technology & rdquo; It is learned from the notice that the application of stainless steel pipe technology and product is of great significance to improve the grade of modern buildings in China and improve and ensure the water quality of water supply.　　≥TS（Mpa）The back is not protected by argon, and the flux cored wire + TIG process has been applied in China for several years. Flux cored wires such as et-elt-et-elt-t-et-elt- have been produced and applied to field welding, and good economic benefits have been obtained.Project scope,Formula for hydraulic test pressure of stainless steel welded pipe for weight calculation fluid (gbt-): where: P - test pressure, MPa; R - stress, taking yield point of %, MPa; s - nominal wall thickness of steel pipe, mm; D - Nominal outer diameter of steel pipe, mm.According to the purpose, it can be divided into oil well pipe (casing, oil pipe and drill pipe), pipeline pipe, boiler pipe, mechanical structure pipe, hydraulic prop pipe, gas cylinder pipe, geological pipe, chemical pipe (high-pressure chemical fertilizer pipe, petroleum cracking pipe) and marine pipe.Deburring: after the pipe is cut off,BerlinCorrugated plate stainless steel, the burr shall be removed to avoid cutting the sealing ring.

Since the back is not filled with argon, its advantages are obvious, mainly for its simplicity and low cost, which is suitable for installation on the construction site. However, due to its structural characteristics, flux cored welding wire has high requirements for welders during operation, with fast wire feeding speed and high wire feeding accuracy. It is difficult to master. Welders should be specially trained and skilled before they can participate in welding in Yangba, Nanjing And foreign construction sites we have successfully solved the problem that argon cannot be passed through the junction and repair port.Sampling inspection, martensitic stainless steel is marked with and C, dual phase (austenite ferrite).For the steel pipes bearing fluid pressure, hydraulic test shall be carried out to test their pressure resistance and quality. If there is no leakage under the specified pressure,BerlinStainless steel honeycomb tube, or they are qualified. Some steel pipes shall also be subject to crimping test, flaring test and flattening test according to the standard or the requirements of the demander.Hardness test: annealed stainless steel pipes with inner diameter of more than mm and wall thickness of less than mm can be tested by w-b Vickers hardness tester, which is very fast and simple, and is suitable for rapid and nondestructive qualification test of stainless steel pipes. For stainless steel pipes with inner diameter of more than mm and wall thickness of more than mm, Rockwell hardness tester shall be used to test HRC hardness. Stainless steel pipes For stainless steel pipes with inner diameter greater than mm and wall thickness less than mm, the surface Rockwell hardness tester shall be used to test HRT or hrn hardness. For stainless steel pipes with inner diameter less than mm and greater than mm, the special Rockwell hardness tester for pipes shall be used to test hrt hardness. When the inner diameter of stainless steel pipes is greater than mm,When the stainless steel fixed port is welded, it will be difficult to ventilate on both sides of the weld. At this time, how to ensure the argon filling protection on the inner side of the weld has become a difficult problem. For a long time, facing the national high price the reasonable price and perfect service of all kinds of stainless steel plates, stainless steel coils, ventilation from the weld center and sealing with adhesive tape on the outside (see Table ).The back is blocked with blocking plate for ventilation protection; Only soluble paper or the combination of soluble paper and blocking plate is used for blocking ventilation protection; Use flux cored wire for backing TIG welding.Brinell hardness in stainless steel pipe standards, Brinell hardness is widely used, and the hardness of the material is often expressed by indentation diameter, which is intuitive and convenient. However, it is not suitable for steel pipes with hard or thin steel.