Key technical characteristics of alloy pipeThe sodium cyanide passivation treatment of alloy pipe can be divided into four categories. Before passivation treatment, the surface of alloy pipe shall be clear of oil stains, pickled and passivated. Passivation treatment can be carried out only after the surface is cleaned, and the workpiece of alloy pipe products can be infiltrated into aqueous solution. The passivation treatment of the alloy tube in sodium cyanide transforms the surface layer into a very thin passivation treatment film, which determines that the color of the surface layer has no change before and after passivation treatment, and the reproducibility of the solution is good.Concepcion,The smooth of steel pipe is mainly through tension reducing, which is a continuous rolling process of hollow base metal without center and tip. Under the condition of ensuring the capillary welding quality, the whole welded pipe is heated to more than ℃ by the welded pipe tension reduction process, and then rolled to finished pipes with various outer diameters and wall thicknesses by the tension reduction machine ( times in total). The fluid pipes produced by developed countries in the world have adopted the welded pipe smooth process in a large number of boiler pipes. With the development of society,ConcepcionQuotation of welded pipe manufacturer, the I-beam flange should be stressed, that is, the I-beam should be standing rather than lying down.Kayanza,I-beam, also known as steel beam, is a long strip of steel with I-shaped section. I-beam is divided into ordinary I-beam and light I-beam. It is a section steel with I-type section shape.The finished product has smooth surface, low friction coefficient, flatness error + / - mm / m length, wear resistance and maximum temperature of ℃Alloy pipe is a very important way and type of seamless steel pipe. Its use is relatively common. It is widely used in various engineering projects, house construction and building decoration. Its fracture will always be found in the production, manufacturing and key marketing of alloy pipe, That is, many stages of production and processing are not done well. Another is that the seasoning is not enough and the proportion of chemical molecules is wrong. There are all reasons.

I-beam: national standard * what is the wall thickness of I-beam Material requirementsIn order to make the welded pipe have the required mechanical, physical and chemical properties, in addition to the reasonable selection of materials and forming process, heat treatment process is often necessary. In addition, the mechanical, physical and chemical properties of aluminum, copper, magnesium, titanium and their alloys can be changed by heat treatment to obtain different service properties.Process inspection, because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different, so it can only be directly used for members bent in the plane of their web or form lattice stressed members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application. I-beam is widely used in buildings or other metal structures.When selecting I-beam in structural design, reasonable I-beam shall be selected according to its mechanical properties,ConcepcionIncoloy800 alloy pipe, chemical properties, weldability and structural size.d. All machines and equipment in a production line can connect with the software of the computer data collection system to complete the timely transmission of data information, and the performance parameters in the production process are monitored by the central control room.

The wear resistance fracture toughness, impact toughness and bending strength under different process conditions were compared, and then the heat treatment process of GCrMo was determined. Development and application of ZYS- bearing damping and antirust oil. Bearing is a new type of multial damping and antirust oil. It takes refined mineral oil as the base oil and is equipped with various additives such as antirust and antifriction. Through comparison test, matching test with lubricating grease and user test, it is proved that ZYS- bearing damping and antirust oil has outstanding damping effect and good antirust lubrication performance.Inspection items, Small longitudinal crackGalvanized pipes are used in construction, machinery manufacturing, steel construction and other projects shipbuilding,ConcepcionIncoloy800H alloy pipe, solar power generation support, steel structure engineering, power engineering, power plant, agricultural and chemical machinery, glass curtain wall, automobile chassis airport, boiler construction, highway railing, house construction, pressure vessel, oil storage tank, bridge, power plant equipment Hoisting and transportation machinery and other welded structural parts with high load.The shape of small longitudinal crack on the surface of alloy pipe is less than mm The overall width is less than mm The depth is lower than .mm.Concepcion,Methods of exerting efficiency in application of C-section steelC-section steel has uniform zinc layer, smooth surface, strong adhesion, no zinc scar, no zinc leakage and high dimensional accuracy. All surfaces are wrapped by zinc layer, and the zinc content on the surface is usually -g /? It has long service life, because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different, so it can only be directly used for members bent in the plane of their web or form lattice stressed members. It is not suitable for axial compression members or members with bending perpendicular to the web plane