SichuanOutdoor guide rail type cargo elevatorMain factors of industry buying
release time:2023-05-11 18:57:37

Secondly,SichuanGuide rail type lifting cargo elevator, there must be no dirt on the friction surface. If there is dirt it needs to be washed off with gasoline or thinner; the gear box, gearbox, external gear and other parts of the equipment and the hydraulic oil must be in accordance with the requirements in the table; Correctly maintain the hydraulic guide rail lift. Regularly check whether the wire ropes in each part are broken or loose. If this phenomenon is found, replace them in time. If there is any looseness, it should be tightened in time. The connecting bolts of the equipment should be checked for tightness when the body is under pressure. All connecting shafts should be equipped with cotter pins; check whether each mechanism is operating normally, whether there is noise or failure , to eliminate all faults in a timely manner; when installing, dismantling and adjusting the slewing mechanism of the equipment, it is necessary to pay attention to the parallelism between the reducer and the center line of the gear, and the appropriate meshing gap; conduct a comprehensive inspection of the equipment regularly, whether the wires and cables are If there is damage, whether the motor is overheated replace it in time and continue to run after troubleshooting; ensure that the bearings of the motor, each box, distribution box and brushes must be kept clean, and the travel switch points of each safety device must be safe and reliable.The cleanliness of the hydraulic station is an important aspect of the elevator hydraulic station, so it should not be careless. Moreover, from a professional point of view, there are relevant rules and requirements, and you should refer to the specification manual, so that you can have a correct understanding and know how to achieve better cleanliness.Sichuan,Regular inspection and maintenance, elimination of hidden dangers, prolonging the service life of equipment and ensuring the safety performance of the elevator.Naturally connect the motor to the lift. When connecting, it must be ensured that the concentricity of the output shaft of the elevator is consistent with that of the input shaft of the motor, and that the outer flanges of the two are parallel. If the concentricity is inconsistent, it will cause the motor shaft to break or the elevator gear to wear.Lo Prado,Low cost: The cost is much lower than that of the scissor-type mobile lifting platform, so when purchasing a lifting platform, you must consider the scope of use of the lifting platform, the frequency of work, the load and other factors to choose a lifting platform that suits the work requirements .What kind of function can be achieved by installing the elevator? Before installation, confirm whether the motor and the elevator are intact, and strictly check whether the dimensions of the parts connected to the motor and the elevator match. Here are the dimensions of the positioning boss of the motor, the input shaft and the groove of the elevator. Fitting tolerances.The daily maintenance of the hydraulic lifting platform in normal use is essential, but even if there is normal maintenance on the equipment, any possible problem cannot be ignored, so in order to ensure that the process of using the hydraulic lifting platform for each operation What aspects do we need to check before operation? Today, the editor will give you a popular science.


SichuanOutdoor guide rail type cargo elevatorMain factors of industry buying



The safety device and application of the guide rail hydraulic lifting platform The use of the guide rail hydraulic lifting platform The guide rail hydraulic lifting platform is a non-scissor hydraulic lifting freight elevator. It is used for goods between different floors of industrial plants, restaurants, restaurants etc. The low height can be made to -mm. The advantage is that it can be placed directly on the ground without digging pits, reducing engineering construction costs, and there is no need to set up hanging points on the top, and can be non-calibrated according to customer needsSeveral types: Motor winding open circuit. When one of the motor windings is disconnected, the three-phase current will be unbalanced and the motor will overheat.The main structure and application of the guide rail elevator: the mechanical part of the guide rail elevator mainly includes three parts: the lifting device, the track device and the belt changing device. The main function is to provide the moving track to make the operation more smooth. The belt changing device is used to switch the track when the elevator is going to pass the door. Lifting device The internal structure of the lifting device is mainly composed of gear mechanism, bracket worm gear, guide mechanism, boom, upper and lower shells, etc. Gear mechanism The gear mechanism mainly includes large and small gears, a winding wheel, a middle shaft, and a safety device composed of a stop buckle and a torsion spring.This kind of fixed lifting equipment can also be used in the warehouse. For example, a certain floor in the warehouse needs to be lifted to send goods or personnel into the designated warehouse.The cheapest,Are the water cooling and air cooling of the hydraulic station the same?What are the maintenance rules for hydraulic lift machinery? The brakes of each mechanism should be checked frequently and the gap between the brake shoe and the brake wheel should be adjusted to ensure flexibility and reliability. There should be no dirt on the friction surface, and if there is dirt, it must be washed off with gasoline or thinner.Before using the aerial work platform, it is necessary to confirm whether the outriggers are well supported, refer to the level beads on the equipment to judge and debug, and then proceed with the operation; the rollers and slideways confirm whether the roller slideways of the hydraulic lifting platform are dry, and if there is When drying the site, an appropriate amount of butter should be added to ensure the smoothness during operation and to avoid head-to-head wear between mechanical parts.


SichuanOutdoor guide rail type cargo elevatorMain factors of industry buying



After the goods are transported, clean up the debris on the platform.Trustworthy,Before using the aerial work platform, it is necessary to confirm whether the outriggers are well supported, refer to the level beads on the equipment to judge and debug, and then proceed with the operation; the rollers and slideways confirm whether the roller slideways of the hydraulic lifting platform are dry, and if there is When drying the site, an appropriate amount of butter should be added to ensure the smoothness during operation and to avoid head-to-head wear between mechanical parts.Overview of the development of scissor-type aerial work platforms: The use of aerial work platforms originated in North America in the s. Products similar to the current vehicle-mounted aerial work platforms began to be used in North American farms for fruit picking and tree branch pruning.Anti-corrosion measures for the body of aerial work vehicles Pay attention to small scratches. The paint surface of aerial work vehicles is often corroded. In addition to common collisions, small rocks on the driving tires, and a small rust will appear after a long time. Because most of these scars are small, they are easy to ignore. Therefore, check regularly, the engine compartment cover and its surroundings, and once found, go to a professional beauty shop for processing.Sichuan,The motor connection is wrong. When the delta connection motor is wrongly connected into a star shape, the motor still runs with full load, and the current flowing through the stator winding will exceed the rated current, and even cause the motor to stop by itself. If it overheats, it will burn out. When the star-connected motor is wrongly connected into a triangle, or the motor with several coil groups connected in series to form a branch circuit is connected in parallel with two branches, it will cause the winding and core to overheat, and in severe cases, the winding will be burned.Features of hydraulic lifts: According to the working mode hydraulic lifting platform products are divided into crank arm hydraulic lifting machines, mast type hydraulic lifts scissor hydraulic lifting machines,SichuanGuide rail lifting cargo elevator, and straight arm hydraulic lifting machines. The hydraulic lift is a replacement product of the folding arm lift (lifting platform) and the scissor lift (lifting platform). It can be widely used in stations, docks, airports, post and telecommunications, municipal gardens, garages, cleaning companies, public building facade decoration, decoration or installation and maintenance of power systems, etc. The lift has the advantages of light weight, self-propelled, electric start, self-supporting legs,SichuanSimple lifting cargo elevator requires, simple operation, large working area, especially the ability to cross obstacles for high-altitude operations and the like.Goods should be stacked on the platform and not tilted. When the freight elevator goes up and down beyond the range of the platform, no one should stand around to watch.


comment list
©2009-2024Metal Microblog  Sitemap