the scope of application is small.Generally, the moisture content of non dry wooden keel is about %,StamboliyskiAnticorrosive wood floor, and that of qualified wooden floor is generally about %. If the humidity difference is too large the wooden floor is easy to absorb moisture quickly. If the time is long, the floor will arch up and the paint will crack.Therefore, it is best to choose dry and straight wood as keel.After the keel level is determined, the keel and floor can be fixed with nails.Stamboliyski,Fifth, strong ground anti-skid.Feature editing voiceJomboy,Laminate flooring is suitable for meeting rooms, offices, etc. it can also be used for the ground decoration of medium and high-grade hotels, restaurants and civil houses.Although laminate floor has moisture-proof layer, it should not be used in wet places such as bathroom and toilet.The first is the type of raw material.When purchasing solid wood multi-layer wood floor you should pay attention to whether the floor is the same material and whether the surface has defects such as crack, rot, skin clip, dead joint, moth eaten, moldy and so on.The general high-quality solid wood multi-layer wood floor shall have clear lines and bright colors on the surface. Mild warm color flooring is strongly recommended for homes for the elderly and children.Mild and warm colors can make people comfortable and cheerful, so choose such a floor suitable for the elderly and children.Some people say this method is unscientific and laminate flooring can&#;t soak in water, but I have done some experiments and come to another conclusion.

The third is color.Some customers are very strict about the color of the floor and must maintain the same color difference.But this provision is unscientific.Because the wood is affected by the sun, raw material parts, growth and development parts and lower sawing points, it will inevitably cause inconsistent color difference. Select the content standard of dispersed formaldehyde. In terms of foot feeling, solid wood is better than reinforcement. According to national industry standards, all solid wood is mm thick, and wood keel ceiling is selected for installation,Common cost methods for solid wood flooring are as follows:Some people say this method is unscientific and laminate flooring can&#;t soak in water, but I have done some experiments and come to another conclusion.The first kind: pungent taste. If the floor tastes like this, it means that it contains a lot of formaldehyde. You need to be careful when choosing. You&#;d better not buy it;

In addition, there are impact resistance, anti-static, anti environmental pollution, anti sunlight, anti smoke, easy installation, easy maintenance, etc.Total quality management,The first is cleaning to remove oil stains or dust;The second is leveling. The convex part shall be shoveled and polished. The concave part can be made into paste with glue and cement at the weight ratio of :, leveled with a spatula, and then leveled with sandpaper after drying.After the ground is flat, clean and dry, it can be glued and paved.Gluing is the last process before paving and the tool shall be a toothed rubber scraper.During gluing, glue shall be applied on the ground according to the size of the floor paint cloth, and one piece shall be paved in this order.A width of cm shall be reserved at the joint of the floor paint cloth. No glue shall be applied first, so that the joint can be treated finally.When the glue coated on the ground feels sticky by hand, it can be paved. When pasting, pay attention to aligning the sidelines, and use a long handle floor brush to blow out and compact.The joints are generally spliced by overlapping cutting, and the overlapping width is about cm.Align the long steel ruler with the center of the overlap, then remove the cut edge strips (note that there should be two edge strips, apply an appropriate amount of glue to the joint with a paint brush, and then close and compact the joint with a pressing roller.The residual glue extruded at the joint shall be wiped clean to avoid affecting the appearance.Then apply a thin layer of joint liquid along the joint.Finally, check whether there are bubbles and whether they are flat.If there are bubbles, use a syringe to insert and suck out the air, and then compact it.Finally, use washing powder to remove the residual glue marks on the lacquer cloth. If they cannot be removed, they can be wiped with alcohol.In this way, the whole process will be completed.Due to the improvement of the living standards of Chinese residents, the grade of interior decoration is also rising, and the decoration materials are increasingly developing towards the fixed decoration direction of elegance, high profile, long service life and good effect.As for the ground, the service life of paint, carpet or ordinary floor leather and floor brick is not as long as that of ground lacquer cloth.Laminate floor is composed of wear-resistant layer, decorative layer, base material and balance layer.The wear-resistant layer, decorative layer and balance layer are manually printed. The base material is made of fast-growing forest materials, which is lower than that of solid wood floor. At the same time, it can be produced on a large scale and has high cost performance.According to different substrates the price difference is obvious, and customers have more room to choose which is suitable for people of all levels.In short, floor leather is a layer of synthetic plastic decorative products. In addition to many advantages such as wear resistance, corrosion resistance, moisture resistance, small water absorption simple construction, convenient maintenance and low price, it also adds the advantages of comfortable foot feeling, narrowing the gap between wood floor and wood floor. No wonder floor leather will be so popular.If you are also worried about the shortcomings of wood flooring, you might as well consider floor leather materials.Plastic floor leather has the advantages of light weight, elasticity,StamboliyskiIs the floor leather afraid of heat, good mechanical strength, good foot feeling strength, foot feeling, wear resistance, pollution resistance, corrosion resistance, heat insulation,StamboliyskiSolid wood composite floor, sound insulation, moisture resistance, small water absorption, good insulation, self extinguishing, easy cleaning, simple construction, convenient maintenance and low price. In a large number of civil buildings and public places, factories with high requirements for cleanlinessIt is widely used in the laboratory.Plastic floor leather belongs to soft floor. It is a floor roll produced by coating or calendering on sheet continuous substrate with polyvinyl chloride resin as the main raw material and appropriate additives.The length of each roll of plastic floor leather is m ~ m, the width is mm ~ mm, and the total thickness is mm (household) ~ mm (public building).Stamboliyski,We hope these techniques will help simplify the plan for installing new floors.If you plan to renovate your house and add new floor elements, please provide room sizes free of charge!Obtain expert estimates to understand how many floors are needed to better determine the project budget.SPC floor is composed of thickened wear-resistant layer, UV layer, color film texture layer and substrate layer.European and American countries call this kind of floor RVP (rigid vinyl plate), rigid plastic floor.The base material is a composite plate made of stone powder and thermoplastic polymer materials after mixing evenly and then extruded at high temperature. At the same time, it has the properties and characteristics of wood and plastics to ensure the strength and toughness of the floor.Wear resistant layer: PVC transparent wear-resistant layer, with a thickness of about .mm, transparent texture, strong adhesion, wear resistance and scratch resistance, and the wear-resistant coefficient can reach - revolutions.[] From the surface coating, there are aluminum oxide, melamine and piano paint. Soak in water