Use Hydraulic lifts are widely used in various industrial enterprises and production lines such as automobiles, containers, mold manufacturing, wood processing, chemical filling, to meet the lifting needs of different operating heights, and can be equipped with various table forms (such as balls, rollers,Reggio Di CalabriaChain guide rail lifting cargo elevator,Reggio Di CalabriaGuide rail chain lifting cargo elevator, Turntable steering, tilting, telescopic), with various methods (separate, linkage, explosion-proof), with the characteristics of stable and accurate lifting, frequent starting,Reggio Di Calabria2 ton cargo elevator, large load capacity, effectively solving the difficulties of various lifting operations in industrial enterprises, so that Production operations freely. The professional elevator factory has advanced technology, strict testing, more affordable prices, and more discounts are in progress, welcome to consult.The hydraulic lifting platform is widely used in the maintenance of industrial and mining enterprises, municipal construction, and decoration of hotels and hotels, with reliable quality and perfect performance.Reggio Di Calabria, and the corresponding anti-slip work should be done; remove the gear box of the equipment, remove the shaft holding oil box take out the lower tile and oil absorber; test the car slowly, and check whether the surface around the shaft holding diameter is severely damaged ; If the damage is serious and the tungsten gold is occupied, it should be smoothed with oilstone; under the motor, and the sleeper is carried on the edge of the ditch inside the rail, and the motor is regularly pulled by a jack to remove the upper tile; the important part of the lifting platform How to deal with equipment damage Check the status of the bearing bush and oil absorber, investigate the cause of damage, replace the bearing bush, clean the shaft oil box; after assembling all parts, install a new oil absorber on the oil box for the shaft, clean the shaft Oil; gear box gear oil in accordance with the regulations; axle box bearing burnout is the most common bearing burnout of the outer row, the axle box and the wheel set will be fixed together, affecting the operation of the equipment.When installing, dismantling and adjusting the slewing mechanism, care should be taken to ensure that the centerline of the slewing mechanism reducer is parallel to the centerline of the gear, the meshing surface is not less than %, and the meshing clearance is suitable.T é bessa,The safety device of the guide rail hydraulic lifting platform The mechanical part of the guide rail hydraulic lifting platform mainly includes the hydraulic system and the mechanical device.The cleanliness of the hydraulic station is an important aspect of the elevator hydraulic station, so it should not be careless. Moreover, from a professional point of view, there are relevant rules and requirements, and you should refer to the specification manual, so that you can have a correct understanding and know how to achieve better cleanliness.Safety performance: The lifting structure is made of high-strength manganese steel rectangular tube, and the scissor-type mechanical mechanism is easy to maintain, with strong stability and high carrying capacity. The maximum lifting height is about meters and the maximum load is about tons. .

The contact opening and closing of the travel switch of each safety device must be reliable, and the contact arc crater should be polished in time.Regular inspection and maintenance, elimination of hidden dangers, and troubleshooting are all good for improving work efficiency, prolonging the service life of equipment and ensuring the safety performance of the elevator.The water cooling of the hydraulic station is generally tube-type water cooling, and its type selection is based on the heat load to calculate the heat exchange area, while its air-cooled elevator is carried out by using an air cooler, and it is The heat transfer capacity is calculated according to the heat load, and then the type selection calculation is carried out under the condition that the flow rate can be satisfied. Therefore, these two kinds of cooling are not the same and there is a big difference. Long-term promotion of freight elevator factories and other, Long-term cooperation, mutual benefit and win-win. If you choose the wrong supplier, you will be overwhelmed with all kinds of after-sales troubles in the later stage. Recently, I have seen many netizens report the problem of very loud oil cylinders. Today, the editor will simply popularize the knowledge for everyone.Recommendation and consultation,Are the water cooling and air cooling of the hydraulic station the same?Many customers think that the operating power supply of the hydraulic lifting platform is below the safe voltage of V, and there will be no electric shock. They are wrong. Normally, there will be no electric shock, but if there is improper operation, it will still be very dangerous. So how can we effectively prevent the occurrence of electric shock accidents? Today, the editor will share safety knowledge with you.Prepare the foundation according to the foundation plan, pay attention to the alignment, leveling, and alignment to ensure the level of the foundation and various requirements for use.

What types of lifts are there? There are many types of this equipment, for example, it can be divided into fixed lifting devices and vehicle-mounted lifting devices according to the form of movement. The so-called fixed lifting means that it is generally installed in one place and fixed, and then the lifting operation can be carried out. This type of lifting equipment is generally used more on the assembly line. Some large-scale production lines need to move the material when loading materials. Lifting to a certain position, and then putting it into the production line for production, a special lifting device is required to be fixed at a certain position of the production line.Quality risk,Goods should be stacked on the platform and not tilted. When the freight elevator goes up and down beyond the range of the platform, different materials, different rated loads, and different brand awareness, the prices are also different. The current price of fixed lifts produced in the domestic market: rated load - tons, height of meters, table size mm *mm, the price is about - yuan; the rated load is - tons, the height is meters, the price is about yuan. Rated load, lift height table size of each fixed liftDifferent. (Specific bearing capacity and rising height can be customized according to user requirements)Reggio Di Calabria,The price is guaranteed, the service is guaranteed, and it is a large-scale logistics and storage equipment service company directly operated by the manufacturer. Since the fixed lift is a mechanical device, the quality and performance of the product must be good. Do not accept the products of some manufacturers whose quality is not up to standard, so as to avoid some safety hazards in use.The load of this series of products is divided into . to . tons, and can also be customized according to user requirements, with a load of up to tons.Check the limit switch to see if all the limit switches are loose. If so, please tighten them. Pay special attention to the ultra-high protection stroke of the hydraulic lifting platform to avoid accidents caused by the equipment exceeding the high safety height; check the pins (ear pins and center pins) Check whether the nuts, nuts, screws, etc. are loose if any, should be reinforced immediately; ensure that the hydraulic lifting platform rises and falls smoothly; outriggers (for high-altitude operating platform)