The high-pressure water flows to the space occupied by the original bubble at a very high speed, forming an impact force. The metal surface of the pump was fatigued and damaged by these impacts. Cavitation is caused by air bubble rupture and material stamping due to the difference in air temperature and pressure　　In fact, when the submersible slurry pump is blocked during use, it will not only have a certain impact on the working efficiency of the equipment during operation, but also cause serious damage to the equipment itself, so it is also a reminder that we are using it tooGalabagh,　　 Before using the pump, carefully check whether the cable is damaged, whether the fasteners are loose or fall off, storage and installation.　　 confirm whether the pressure capacity of the pipeline meets the requirements, and conduct hydrostatic test if necessary.Saigu,　　In addition, the sundries inside the pump body and impeller shall be cleaned. Then calibrate the pump shaft and motor shaft of the slurry pump to make them on the same horizontal line.　　Potential is convenient and flexible. It is easy to operate. It can be operated by a fool who turns on the power supply under immersion; It has a wide range of applications. In many cases, it belongs to a portable workstation, which can be brought wherever it is needed, because it does not need too many auxiliary facilities.　　Troubleshooting: first increase the water pressure then inject water into the pump body, and then start the pump. At the same time,GalabaghSmall deep well pump, check whether the check valve is tight and whether the pipes and joints leak. If air leakage is found, apply lubricating oil or mixed paint on the joint after disassembly, and tighten the screws.

　　In fact, it will not only have a certain impact on the working efficiency of the equipment during operation, but also cause serious damage to the equipment itself, so it is also a reminder that we are using it too　　 daily, weekly, quarterly and annual inspection, maintenance and use plans shall be prepared for deep well pumps.　　It is also necessary to clean the ventilation duct to avoid blockage.Variable cost,　　Line direction pay attention to the direction of rotation. Then loosen the original compression nut of the bearing box of the slurry pump of the submersible pump,GalabaghPipeline pump, and then move the rotor assembly towards the motor. Then it is necessary to check the clearance with a feeler gauge δ, When δ= A (. ~ mm　　The solution to the excessive temperature of the water pump: when selecting the motor, it is necessary to select one that matches its power and speed. In addition, the cooling fan should be installed on the main shaft. It is also possible to appropriately increase the number of fan blades, but pay attention to adjusting the vacuum pump　　If the shaft seal is not properly selected, it will not only require frequent maintenance during operation but also leak a large amount of transmitted liquid.

　　The high-efficiency slurry pump has three characteristics: first, the slurry pump has high operation efficiency and low loss.Installation material list,　　The other mechanical seal is a split seal, which can be replaced without disassembling the slurry pump.　　 when the deep well pump is put into water for use, pay attention to protect the cable. The cable must not be stressed to prevent damage. The lifting weight of the lifting device (such as tripod hoist or electric hoist) used shall be greater than the weight of the submersible pump, and enough space shall be reserved. A wood that is tied to the wellhead with a rope　　 selection of pump head: generally, the pump head shall be determined by enlarging the margin of % - %.Galabagh,　　The equipment is integrated with the oil cooler, with compact layout. The water pump meets the modular and integrated design requirements of diesel engine parts. The joint surface with oil cooler adopts rubber sealing method,GalabaghBaigang deep well pump, which has good sealing effect. Submersible slurry pump is a kind of solid-liquid mixing medium with the help of centrifugal force　　The submersible slurry pump and equipment can also choose to add some water inlet detection devices according to the actual use needs. The overheat monitoring devices are often used in a large amount in time, and the pump and motor of the equipment used in time are the same shaft, so　　Stability and reliability of seals between pump bodies.