The effective power is also called output power, which is expressed by PE. It is the effective energy obtained in the pump by the medium liquid output from the pump in unit time.　　Although the shaft seal occupies a small position in the pump the normal operation of the pump is closely related to the shaft seal.Fazabad,　　 Check the suction pipe and bottom valve to see if there is any air leakage source. Remove the silt and other obstructions at the water inlet. Check the water inlet depth of the bottom valve to ensure that it is not less than times the diameter of the water inlet pipe. If it is not enough, deepen the water inlet depth of the bottom valve.　　Normal operation. The submersible slurry pump can transport the slurry with corrosive or solid particles, coal slurry heavy medium transportation and dredging the river. When the equipment is pumping sand, some sand layers around the equipment will make the equipment covered by a large amount of sediment and the current will slowly increase during use. Well, we should choosemexico-city,　　The above four methods can be used to detect whether the submersible slurry pump has cavitation, because if the equipment is in use, it will have a great impact on the operating efficiency. Even if the cavitation time is long, it will also have a certain impact on other parts of the equipment. Sometimes submersible slurry pump　　In recent years, the demand for submersible slurry pumps has increased greatly. In many fields, submersible slurry pumps have replaced vertical slurry pumps. What are the differences between the two? Let&#;s yze.　　After meters,FazabadHorizontal wear-resistant slurry pump, the sealing of the equipment can not bear the water pressure at this depth.

　　 Moreover,FazabadWear resistant slurry pump, the processes of these two pumps are also different, and the sewage pump can generally be adjusted. Submersible pumps are generally used in some special or other places.　　The answer to this question must be! Submersible sewage pump has attracted more and more attention because of its wide range of applications and strong sewage treatment capacity, but improper use and maintenance will lead to submersible sewage.　　 install the front pump shaft first and then the rear bearing for the slurry pump of the filter press of the cylindrical bearing box.superior quality,　　The type selection design of submersible slurry pump has a great impact on the service life and operation stability of slurry pump. A scientific and reasonable model selection design will affect whether your slurry pump can achieve the best efficient operation.　　; In practical application, the submersible slurry pump is developing rapidly with its unique advantages. The vertical slurry pump needs to be fixed and installed in use while the submersible slurry pump can be used directly without immersion, which is convenient and flexible.　　Moreover, explosive and toxic liquid will cause fire, explosion and poisoning,FazabadSubmersible sewage pump, and the consequences will be unimaginable.

　　 determination of model: for water pump or pump with physical and chemical medium similar to water, it is necessary to go to the relevant product catalog or sample, and make correction according to the performance table or performance curve of the model to see whether the normal working point falls in the priority working area of the pump.Total quality management,　　 Why does the demand for submersible slurry pumps increase greatly? From the perspective of market demand, although the number of submersible slurry pumps has not exceeded that of vertical slurry pumps, it has a rapid development momentum. The main reason is that the above-mentioned use is convenient and flexible; In addition, the application market of submersible slurry pump is also better than that of vertical pump　　Replace the ball bearing of the motor.　　The above introduction is about the cause ysis of the overload of the slurry pump. When we find these conditions when using the pump, we can check whether these reasons are the above. This is also a reminder that we need to maintain the pump during normal use. latentFazabad,　　Friction. Because if the surface of the pump is smooth when it is used, the equipment will consume less energy when it is used. Generally, close the cock of the vacuum gauge and pressure gauge and the gate valve on the water outlet pipeline, and After that, cut off the power supply of the motor. If the temperature of the environment is low, open the square plug at the lower part of the pump body to remove the remaining water to avoid frost cracking. During operation, the maximum temperature of the bearing shall not exceed ℃, and the quantity of calcium base grease used for lubricating oil bearing shall be the same as that of the bearing body　　The seal cannot bear the water pressure at this depth. Once the water leaks, the motor will not work normally