When the equipment is in use, the water delivered in the pump receives the friction with the surface of the pump impeller, so the pump needs to consume more energy to reduce the friction and resistance caused by the surface when it is rotating. Water will slowly overcome it as it flows　　The use of water pumps is related to all aspects of our life. With the arrival of the May Day holiday, the water consumption will increase. Therefore, it is necessary for us to choose a suitable water pump.Muharak,　　 estimated installation depth of pump M　　 install the front pump shaft first and then the rear bearing for the slurry pump of the filter press of the cylindrical bearing box.Zabure,　　 It may be that the motor power of the water pump is too large, the working current is too large, and the heat generation is too large, resulting in the high temperature of the vacuum pump.　　 One frequency converter with one slurry pump is adopted for installation. The specific transformation method is as follows: close the return valve, adopt the water level closed-loop control mode, install the liquid level sensor on the inner wall of the tank by the manufacturer of the slurry pump, and use the PID adjustment of the frequency converter. When　　Second, so the motor temperature will be too high after long-term overload operation; In addition, frequent startup during use will also lead to fever, so I

　When using the submersible slurry pump the equipment may be burned out. The main reason for this phenomenon is improper operation. How should we prevent the burning out?　　 The pump fails to supply water or the flow is insufficient. The pump fails to supply water or the flow is insufficient. It is likely that the suction pipe has water leakage or the bottom valve has air leakage, but there are several possible reasons: the water inlet is blocked; The bottom valve is not deep enough underwater; The running speed of the water pump is not enough; leaf　　 Precautions for disassembly of submersible slurry pump Before disassembling the filter press, make sure that the liquid in the submersible slurry pump is completely discharged. If the rotor is disassembled, drain the lubricating oil in the rotor bearing housing. If the newly added oil is stored, it should continue to be used after maintenance. Do not dump it directlyRange,　　What is the cause of pump overload.　　 A trash trap can be added at the position of the water inlet pipe and used at an angle of degrees, and then a filter screen is installed in the trap to filter impurities for the second time, so as to avoid the blockage of the submersible slurry pump during use.　　 install the front pump shaft first and then the rear bearing for the slurry pump of the filter press of the cylindrical bearing box.

　　Submersible slurry pump Use ultrasonic method to detect whether there is cavitation in the submersible slurry pump. This method is often convenient for re detection. Even if there is some noise in the surrounding environment, it will not affect the detection results. Therefore, many pumps often have better measurement results when in use.Direct material　　Basically, the reasons for the motor heating of the submersible slurry pump are the above items. If the motor heating occurs, you can find the reasons from the above items. However, it must be noted that if the fault is caused by electricity, people who do not know electricity should not repair it by themselves, so as to avoid people　　 during operation, the deep well pump shall rotate smoothly without vibration and abnormal sound. Observe whether there is obvious fluctuation in the motor running current and line voltage before and after startup. The change of water level in the well shall be observed frequently. The motor must not be exposed to the water surface or sink into the sludge to avoid affecting the power supply　　Work no noise and vibration, and the site is cleaner.Muharak,　　Submersible slurry pumps generally need to use some composite materials for manufacturing when they are used, so that they can have good wear and corrosion resistance when they are used, and can be used to transport most of the media when they are used. Phreatic slurry　　Submersible pump is a common water lifting equipment for deep wells. During operation, the whole machine intrudes into the water to extract water from the underground to the surface. It is commonly used for domestic water,MuharakHorizontal wear-resistant slurry pump, mine rescue,MuharakPipeline pump, industrial cooling, farmland irrigation, seawater lifting, ship load adjustment,MuharakSelf priming slurry pump wholesale, landscape fountains, etc. Submersible pump is generally divided into clean water submersible　　Moreover, it is often troublesome to install it. Therefore, the place where it operates will also be limited. If the equipment will