BarneyISG single stage vertical pipeline pump,

　　The submersible slurry pump is developed to adapt to the increasingly complex working conditions and facilitate the use of users. Its use mode is more flexible. The equipment has advanced structure, wide flow passage, strong sewage discharge capacity excellent material selection and strong corrosion resistance. Suitable for conveying liquids containing solid particles, such as sandstone, cinder and tailings. So what are the requirements for its work? Let&#;s understand briefly.　　 Precautions for disassembly of submersible slurry pump Before disassembling the filter press, make sure that the liquid in the submersible slurry pump is completely discharged. If the rotor is disassembled, drain the lubricating oil in the rotor bearing housing. If the newly added oil is stored, it should continue to be used after maintenance. Do not dump it directlyBarney,　　It is not allowed to operate the electric pump under the condition of low lift for a long time (generally, the operating lift shall not be less than % of the rated lift), which shall be controlled within the recommended operating lift plan as far as possible to prevent the electric pump from burning out the motor due to overload. Pumps without self circulating cooling equipment prevent all of them from being exposed to the water for a long time　　There is a difference between submersible slurry pump and sewage pump. Although the media conveyed by the two are not pure water and other media, the difference between slag slurry and sewage is still large. Let&#;s take a look at the difference between the two.Bhatpara abhaynagar Hotel,　　When the slurry pump is working, the pump needs to be placed on land, the suction pipe in water, and the pump needs to be started. Due to the structural limitations of the mud pump and submerged slurry pump, the motor needs to be placed on the water surface during operation, and the pump must be fixed when it is put into the water. Otherwise, the motor will fall into the water　　The above is a brief introduction to the effect and form of shaft seal of submersible slurry pump. Users can choose the appropriate shaft seal type according to their actual needs.　　Slurry pump Inappropriate model is selected when selecting the pump. In actual use,BarneyVertical slurry pump, when the load conditions do not match the model of the slurry pump, the pump lift used is too high or too low, which will lead to overload, so we are selecting the pump

　　Submersible pump is a common water lifting equipment for deep wells. During operation the whole machine intrudes into the water to extract water from the underground to the surface. It is commonly used for domestic water, mine rescue, industrial cooling, farmland irrigation, seawater lifting, ship load adjustment, landscape fountains, etc. Submersible pump is generally divided into clean water submersible　　 check the cable and replace it if it is broken or broken to avoid leakage.　　In the application of pumps, the first thing we think of is water. Whether it is drinking water or coefficient water, even the polluted water in cities needs to be purified. All these require its equipment to provide services for us. Without pumps, our basic survival is a problem.Quality assurance,　　Troubleshooting: first increase the water pressure, then inject water into the pump body, and then start the pump. At the same time,BarneyCentrifugal slurry pump, check whether the check valve is tight and whether the pipes and joints leak. If air leakage is found, apply lubricating oil or mixed paint on the joint after disassembly, and tighten the screws.　　It is an auxiliary means for some on-site monitoring.　　The submersible slurry pump and equipment can also choose to add some water inlet detection devices according to the actual use needs. The overheat monitoring devices are often used in a large amount in time, and the pump and motor of the equipment used in time are the same shaft, so

　　 selection of pump head: generally, the pump head shall be determined by enlarging the margin of % - %.Economic management,　　Line direction pay attention to the direction of rotation. Then loosen the original compression nut of the bearing box of the slurry pump of the submersible pump, When δ= A (. ~ mm　　 water quality: fine sand; Zhongsha; River and river water　　The Tao part also consumes part of it.Barney and then move the rotor assembly towards the motor. Then it is necessary to check the clearance with a feeler gauge δ,　　The vertical sand pumping pump is popular with a wide range of sand pumping pump users because it is easy to move. This equipment is made of high-tech endurance data. Its service life has been greatly improved, and the maintenance frequency has been reduced, and the income has been increased.　　 Then reinstall the equipment on the engine and install the rubber hose.　　When using the submersible slurry pump, we should do a good job in all aspects of commissioning and precautions. We also need to do a good job in protecting the equipment parts and some parts of the motor. Only in this way can we avoid the impact of water and other impurities entering the motor