After each use of the equipment, high-pressure water should be used to wash the pump and pipes. The washing can be stopped until the water has no impurities.　　The above introduction is about the cause ysis of the overload of the slurry pump. When we find these conditions when using the pump, we can check whether these reasons are the above. This is also a reminder that we need to maintain the pump during normal use. latentKarbala,　　Although they are both pipeline pumps among centrifugal pumps, there are still many categories. Next, let&#;s talk about some models of pipeline pumps and their respective uses.　　The non service life of the equipment is not as long as possible. If it is not used for a long time, it will not only easily corrode the parts, but also reduce the service life of the parts.Sittwe,KarbalaHH slurry pump,　　Third, the whole industrial and mining system operates stably, and the operation of the pump will not affect the work of the whole industrial and mining system.　　 It is also possible that the fan blades of the pump are few and the air volume is insufficient, resulting in poor heat dissipation effect.　　Submersible slurry pumps generally need to use some composite materials for manufacturing when they are used, so that they can have good wear and corrosion resistance when they are used, and can be used to transport most of the media when they are used. Phreatic slurry

　　First, the reason for the motor body: the wrong connection will make the temperature rise rapidly when the equipment is used; In addition, there may be some phase to phase short circuits between stator windings, so when the situation is relatively minor, the motor is only in local places　　Finally select the appropriate pump model according to the determined Q and H. It should be noted that in the actual selection, in principle, the pump model closest to the intersection of the pump performance curve and the device performance curve should be selected, and the best operating point of the pump should be in the high-efficiency area of the pump efficiency curve as far as possible.　　 add water with manual pump. Some pump owners have their own hand pumps. They can also buy or manufacture their own small hand pumps. The gate valve shall be installed at the water inlet. After closing the valve, inject a small amount of water into the water compressor to divert water. When the hand pump discharges water, it means that the pump is fullInformation recommendation,　　 When starting the slurry pump, the outlet gate valve shall be (closed or slightly opened by /. Before starting the slurry pump, the motor can add a variety of protection devices such as water inflow detection and overheating slowly start the pump outlet valve. The size and speed of opening the pump outlet valve should be based on the fact that the pump does not vibrate and the motor　　According to the user&#;s requirements, so that the product can operate safely for a long time under adverse working conditions.　　Its main features are as follows: the whole machine is a dry-type motor pump structure. The motor is protected by mechanical seal, which can pump out the slag settled at the bottom after stirring into turbulence. impeller

　　 there is also a simple method to measure the vibration frequency of the pump by vibration method. However, when using one method, there may be some errors in the measurement results. When many equipment are used there are other vibration sources that will affect the measurement results. Therefore, in fact, it is mainlyProduct survey,　　 When adding lubricating oil to the pump at ordinary times, the metering must be controlled, and the excess lubricating oil in the pump must be discharged and replaced regularly.　　 Check and replace accessories regularly: check cables, motor insulation and screws at least once a year. If it is damaged, it should be replaced in time.　　The high-efficiency slurry pump has three characteristics: first, the slurry pump has high operation efficiency and low loss.Karbala,　　Through the introduction, we learned that the submersible slurry pump can be used to transport slurry when it is used at ordinary times. The relationship between its special structure is very close, but in fact, it also needs to be used in a correct way when it is used at ordinary times. Only in this way can　　 First of all, let&#;s understand the causes of insufficient liquid supply: If the liquid level stored in the circulating liquid storage tank is lower than %, then insufficient liquid supply will occur when it is in use. Or the pump adds too much lubricating oil, which leads to accumulation　　It will generate heat, but when it is serious, it will directly burn out the insulation; There may also be some faults in the ventilation system. At this time, it is necessary to check whether the fan of the submersible slurry pump is damaged or rotating