The application of pumps involves all aspects of work and production, and some of the names are very similar, which makes it difficult to distinguish. Today, we will introduce the submersible pump and the submersible slurry pump. Is there any difference between the two　　 Next, it is necessary to check the water seal. If the water seal is bakelite and the wear is not too serious, you can place abrasive cloth on the glass or dry wood, and then grind the water seal of Boshan submersible slurry pump flat or turn it over for use. However, if the thrust rubber water seal is used, whenShemona,　　Solution: replace the remote pressure gauge; Replace the pressure transmitter; Check the connecting signal wire.　　 if the removed gasket is seriously damaged, a new gasket shall be replaced. The removed parts shall be cleaned with kerosene before assembly.Daloa,　　After the submersible slurry pump adds a water gun to the support at the bottom of the submersible slurry pump, the hardened mud layer around the slurry pump will collapse rapidly under the applied water pressure which will also increase the sand pumping area. This will also increase the sand pumping area,ShemonaQuotation slurry pump,　　Cavitation of the pump is caused by water evaporation of the pump. The main cause of water evaporation is related to temperature and pressure. Under a certain pressure,ShemonaWQ submersible sewage pump,ShemonaSewage pump diving, when the temperature rises to a certain value, the water begins to vaporize and change from liquid to gas. On the contrary at a certain temperature, the pressure drops to　　As a submersible slurry pump widely used in many fields, it has the advantages of simple structure, convenient disassembly and maintenance, and convenient installation and use. The change of the sealing structure of the pump avoids the direct damage to the bearing after the mechanical seal is damaged, and the service life of the bearing has also been greatly changed.

　　A large amount of lubricating oil is stored.　　Will the submersible sewage pump get sick?　　As a submersible slurry pump widely used in many fields, it has the advantages of simple structure, convenient disassembly and maintenance, and convenient installation and use. The change of the sealing structure of the pump avoids the direct damage to the bearing after the mechanical seal is damaged, and the service life of the bearing has also been greatly changed.Honest management,　　Start the priming pump. Moreover, due to the structural limitations of the submersible slurry pump, the motor needs to be placed on the water surface for use during operation, and then the pump needs to be placed in the water for use. Therefore, the submersible slurry pump must be　　The submersible slurry pump and equipment can also choose to add some water inlet detection devices according to the actual use needs. The overheat monitoring devices are often used in a large amount in time and the pump and motor of the equipment used in time are the same shaft, so　　When the water level reaches, the frequency of the frequency converter drops, and the slurry pump operates at a low speed. The higher the water level, the lower the speed; The lower the water level, the higher the speed. At the same time, the water level signal is transmitted to the control cabinet so that the operators can timely understand the liquid level. Through this control, the circulation in the slag slurry pool is basically unchanged

　　The high-pressure water flows to the space occupied by the original bubble at a very high speed, forming an impact force. The metal surface of the pump was fatigued and damaged by these impacts. Cavitation is caused by air bubble rupture and material stamping due to the difference in air temperature and pressurePrice,　　The submersible slurry pump is developed to adapt to the increasingly complex working conditions and facilitate the use of users. Its use mode is more flexible. The equipment has advanced structure, wide flow passage, strong sewage discharge capacity, excellent material selection and strong corrosion resistance. Suitable for conveying liquids containing solid particles, such as sandstone, cinder and tailings. So what are the requirements for its work? Let&#;s understand briefly.　　 There is no cavitation damage and water diversion. In particular, the latter point brings great convenience to operators.　　 If the hot water within ℃ is recommended, the hot water pump must be used, and the external tap water shall be connected for cooling during operation,　　The purpose is to inject liquid higher than . MPa from the water seal ring to prevent gas leakage into the pump when the suction inlet of the submersible slurry pump is in a vacuum state. When the water pressure in the pump is higher than . MPa, the sealing fluid .-. MPa higher than the pressure in the pump can be injected to seal and reduce leakage　　The submersible slurry pump shall be shut down for inspection in time in case of machine problems during operation, and regular maintenance shall be done. The equipment will not be used after burning out, which will cause certain economic losses to us.　　If the pump outputs more medium liquid, it will certainly do more work. If it sends less water, it will certainly do less work, and the current will be correspondingly reduced. Pump power (kw) = head (m) × Flow (m/s) × The gravity of the fluid (kg/m for water) divided by (power conversion factor) divided by the efficiency of the pump (about