for new or replaced deep well submersible pumps

　　The slurry pump of underground pump can also work normally.　　 selection of flow: single suction pump or double suction pump shall be selected according to the flow; single suction pump or multi suction pump shall be selected according to the lift.Karat, after hours of use, check whether the seal is good. In the future, check it once a month. At the same time, check whether the shielding sleeve between the motor rotor and stator is well sealed. Try to reduce the number of starts in use.　　 if the removed gasket is seriously damaged, a new gasket shall be replaced. The removed parts shall be cleaned with kerosene before assembly.San Vicente de Canete,　　Now you know the reason why the pump has air turbidity. In fact, this is a very common phenomenon. You don&#;t have to worry about it. Water pump can transport many things, such as water, oil, liquid metal, acid-base night and so on. It is a good means of transport.　　 determination of model: for water pump or pump with physical and chemical medium similar to water,KaratHH slurry pump,KaratVertical heavy-duty slurry pump, it is necessary to go to the relevant product catalog or sample, and make correction according to the performance table or performance curve of the model to see whether the normal working point falls in the priority working area of the pump.　　Will be scrapped. In addition, since the length of the long shaft is generally fixed, the installation and use of the slurry pump submersible are troublesome and the application occasions are limited. The submersible slurry pump is developed to adapt to increasingly complex working conditions and facilitate the use of users. Its use mode is more

　　 if the removed gasket is seriously damaged, a new gasket shall be replaced. The removed parts shall be cleaned with kerosene before assembly.　　Use a V megohmmeter to measure the insulation resistance between the electric pump motor and the phase to ground, and the value shall not be less than megohm. Otherwise, the stator winding of the motor shall be subject to monotonic treatment, and the monotonic treatment temperature shall not exceed ℃.　　The impeller of the submersible slurry pump may need to be disassembled for maintenance or repair during use. However, we may make mistakes during disassembly. Let&#;s take a look at the correct disassembly of the impellerTotal quality management, lift the submersible slurry pump and move it to the adjacent position of the previous sand pumping place to continue pumping sand,KaratRubber lining submerged slurry pump, so as to move the sand pumping place back and forth for sand pumping so that the sand pumping area in this area forms a honeycomb,　　Submersible slurry pumps generally need to use some composite materials for manufacturing when they are used, so that they can have good wear and corrosion resistance when they are used, and can be used to transport most of the media when they are used. Phreatic slurry　　Only in this way can its service life be extended to a large extent.

　　Rotate in the rolling direction until the friction between the impeller and the front guard plate stops, then use the adjusting bolt to move the rotor backward, record the forward and backward movement gap, evenly distribute it between the front and rear guard plates of the impeller until the gap between the impeller, the front guard plate and the rear guard plate is flat, stop,　　The higher the specific speed of submersible slurry pump, the smaller the allowable cutting amount of impeller diameter. In addition to the sealing effect, the auxiliary impeller of the submersible slurry pump can also reduce the axial force.　　 No leakage protector is installed: leakage protector is also known as lifesaver. If the leakage value of the submersible sewage pump is higher than the working current value of the leakage preventer, the leakage preventer will cut off the power supply of the submersible pump to ensure the normal operation of the equipment.　　 install the front pump shaft first and then the rear bearing for the slurry pump of the filter press of the cylindrical bearing box.Karat,　　Strong strength and other advantages. It is widely used as a sealing device for various pumps. Place a water seal ring at the bottom of the packing box, and then place the filler.　　Potential energy, pumping water up high. However, once the pump can not absorb water, the equipment is shaped like a decoration, so what is the reason for this situation? How to solve it?　　The first stage impeller of the pump is disassembled; It is also necessary to screw down the connecting nut between the water absorption section and the bearing body and the bolt on the bearing pressure connection, so that it is convenient for us to disassemble the bearing parts; When the shaft is pulled out from the suction section the fixing nut on the shaft shall be