It is occasionally found that there is insufficient liquid supply when using,　　In fact, as far as whether the vertical pipeline pump has a suction lift is concerned, we can tell that it has a suction lift. But what you need to know is that suction range and self-priming are actually two different concepts.　　 The bus voltage where the motor is located is V. Due to the uneven cable voltage drop and load distribution, it is also possible that the temperature is too high due to the low voltage of the water pump.Nagano,　　 Cutting blades can be selected to cut some large block solid substances into pieces during use, so that blockage can be avoided during reuse.　　 Cutting blades can be selected to cut some large block solid substances into pieces during use, so that blockage can be avoided during reuse.　　The use of water pumps is related to all aspects of our life. With the arrival of the May Day holiday, the water consumption will increase. Therefore,NeshaburLong shaft submerged slurry pump,NeshaburBooster pipeline pump, it is necessary for us to choose a suitable water pump.

　　 Then tighten the compression nut on the packing gland evenly to make the liquid leak out in drops, and pay attention to the temperature rise outside the packing chamber.　　Driven by the pump products represented by stainless steel pipeline pumps, the whole pump industry is constantly moving forward, and with the raw material market driven by this, new stainless steel materials are constantly coming out. The continuous improvement of various technologies and specifications has driven the whole industrial chain to a higher direction.　　Submersible slurry pump is a kind of pump used in mines. Do you know the effect and form of its shaft seal? Let&#;s have a look.Executive standard, the power supply across the country has been tense again, which has driven the hot sale of it and generators in the phase II market. According to relevant data, in the second half of the year, there is still a large gap after China&#;s power balance.　　The of descending axial force can be used for slurry transportation in power plants, hydraulic and other professions; The mechanical seal is tight and reliable,NeshaburSmall deep well pump, and the leakage probability does not exceed drops /min, which is mostly used to transport flammable, explosive, toxic, strong corrosive and valuable liquids or materials with high temperature, high pressure and low temperature.　　Submersible pump is a common water lifting equipment for deep wells. During operation, the whole machine intrudes into the water to extract water from the underground to the surface. It is commonly used for domestic water, mine rescue, industrial cooling, farmland irrigation, seawater lifting, landscape fountains, etc. Submersible pump is generally divided into clean water submersible

　　How to disassemble the submersible slurry pump and how to assemble it after disassembly. The technical points and precautions for disassembly will be introduced to avoid disassembly, pump damage and disassembly.Free consultation,　　Basically, the reasons for the motor heating of the submersible slurry pump are the above items. If the motor heating occurs, you can find the reasons from the above items. However, it must be noted that if the fault is caused by electricity, people who do not know electricity should not repair it by themselves, so as to avoid people　　I believe you have such a question when using the submersible sewage pump, that is, is this pump a submersible pump? Or is it a sewage pump? In fact, this question is very easy to distinguish. You can take a look at the following contents sorted out by Shanghai Shenquan.　　 There may also be mechanical failure of the pump, such as serious damage to the bearing of the pump, so that the bore will be 'swept' when the stator and rotor rub against each other, or the impeller will be stuck due to impurities such as water and grass when the pump pumps waterNeshabur,　　If there are sundries blocked, the pump will not be filled with water. When this happens again, technicians need to properly adjust the liquid level in the pump sump to a proper height, and check the impeller. In case of damage or aging, it needs to be replaced in time,　　 If the hot water within ℃ is recommended, the hot water pump must be used and the external tap water shall be connected for cooling during operation, we may make mistakes during disassembly. Let&#;s take a look at the correct disassembly of the impeller

when we do not know the pump structure otherwise the motor will not be burned due to too high medium temperature.　　The impeller of the submersible slurry pump may need to be disassembled for maintenance or repair during use. However