SukabumiSmall deep well pump, the equipment may be burned out. The main reason for this phenomenon is improper operation. How should we prevent the burning out?　　 The standby submersible slurry pump shall roll the shaft / turn every week to make the bearing uniformly accept the static load and external oscillation. The building structure in the water pump room shall be reconstructed. Sound absorbing and isolating plates shall be installed around the wall and on the top of the machine room and fixed with light steel keel; The connecting holes between the machine room and other rooms are tightly blocked,Sukabumi,　　Therefore, it can be directly installed in the sewage tank without building a special pump room to install pumps and machines, which can save a lot of land and infrastructure costs.　　Be sure to choose a pump that is more suitable for use.Copenhagen,　　If the oil seal ring of the shaft is seriously worn, replace it with a new one.　　The use of water pumps for agricultural drainage and irrigation can improve the ability of agriculture to resist natural disasters, increase production and ensure income, and provide material conditions for agricultural mechanization and water conservancy.　　Normal operation. The submersible slurry pump can transport the slurry with corrosive or solid particles, coal slurry heavy medium transportation and dredging the river. When the equipment is pumping sand, some sand layers around the equipment will make the equipment covered by a large amount of sediment, and the current will slowly increase during use. Well, we should choose

　　 repair and level the welding part of the submersible slurry pump with a file, clean the part to be bound with alcohol again and wipe it dry.　　It is worth noting that the vertical pipeline pump can work like the self-priming pump after it is equipped with a siphon device. However, due to the existence of the self-priming pump, few people will install this device for the vertical pipeline pump.　　It is longer and saves production cost. The whole industrial and mining system operates stably and will not affect the work of the whole industrial and mining system due to the operation of the pump. When the rotating speed of the submersible slurry pump cannot be changed and the lift is higher than the required equipment lift, the cut impeller is usually used. The cut isrecommend,　　If the oil seal ring of the shaft is seriously worn, replace it with a new one.　　The hardened mud layer collapses after softening avoiding the phenomenon of burying the pump during use.　　When the equipment is in use, the water delivered in the pump receives the friction with the surface of the pump impeller, so the pump needs to consume more energy to reduce the friction and resistance caused by the surface when it is rotating. Water will slowly overcome it as it flows

　　Submersible slurry pump it fills the gap in the application of slurry pump. When the submergence is deep and there is no good mud outlet, the traditional slurry pump cannot be installed and operated, and the submersible slurry pump can supplement this part of the blank work point.Quality assurance,　　 The submersible slurry pump usually relies on water cooling to dissipate heat. If the motor leaks out of the water without water cooling, so it is easy to burn out the motor.　　Submersible slurry pump is an important equipment in drilling and water intake operations. When the equipment is working,SukabumiVertical multistage centrifugal pipeline pump,SukabumiBaigang deep well pump, it is submerged as a whole. Pumping groundwater to the surface is widely used for domestic water, mine emergency rescue, industrial cooling, farmland irrigation, geothermal heating in residential areas, etc. You will be briefed on it Scope of application.　　Potential energy, pumping water up high. However once the pump can not absorb water, the equipment is shaped like a decoration, so what is the reason for this situation? How to solve it?Sukabumi,　　If the water leakage is serious, the broken pipe shall be dismantled and replaced. Lower the lift and press the nozzle of the water pump into the water for .m.　　In addition to the main impeller inside the equipment, a set of impeller for mixing will be added at the bottom of the equipment, so that some mortar slowly settled inside the equipment can be mixed with water to become a flowing medium, so that the equipment can be used without its　　If the pressure in the local area is equal to or lower than the vaporization pressure corresponding to the water temperature in the flow process, the water will vaporize there and form many small bubbles mixed by steam and gas. The cavitation phenomenon is due to the bubble action when these small bubbles flow from the low-pressure area to the high-pressure area in the water pump