Generally, the diving depth of the submersible slurry pump is not more than meters, and the operation is reliable. Why not more than meters? This is the crucial technical point of the submersible slurry pump, because the current sealing technology in China is more than meters, not because the slurry pump has a problem, but because　　If the oil seal ring of the shaft is seriously worn replace it with a new one.Robat Karim,　　 absorb all kinds of diamond sand, quartz sand, steel slag and water slag solid particles.　　Circumference. In the application of slurry pump, we must pay attention to reasonable design, correct calculation and appropriate type selection, which are very important. In addition to the main wheel a set of stirring impeller is added at the bottom of the product, which can spray the precipitated slag into a mixture of water and solid particlesMale,　　Many people do not know much about the packing and sealing of equipment because of the equipment of mass and energy. Next,Robat KarimWater well pipeline pump,Robat KarimFire deep well pump, let&#;s learn about the packaging and sealing method of the equipment: packing sealing is very common in submersible slurry pumps. This method has good sealing performance, is easy to use, and effectively reduces the wear of the host and anti vibration kinetic energy　　The water pump can be used to transport and pressurize clean water without impurities, such as apartment, residence, villa water supply, factory water supply, water supply system, drinking water system and water treatment. In short, there are many uses.　　 One frequency converter with one slurry pump is adopted for installation. The specific transformation method is as follows: close the return valve, adopt the water level closed-loop control mode, install the liquid level sensor on the inner wall of the tank by the manufacturer of the slurry pump, when we do not know the pump structure, we may make mistakes during disassembly. Let&#;s take a look at the correct disassembly of the impeller　　 After one year of use, check the corrosion of the pump,Robat KarimScrew deep well pump, remove the rust and paint. If the submersible pump is not used for a long time, it should be carefully checked and put dry.　　 When the slurry pump fails to absorb water during operation, it is necessary to check whether the bottom valve is open and make corresponding adjustment.Quality improvement,　　If there is a standby pump, it is recommended that the two pumps be used in turn. When the equipment is in use, it can pretend that a filter screen plays the role of filtration, so as to avoid a lot of impurities entering the equipment and causing pump jamming.　　The submersible slurry pump shall be shut down for inspection in time in case of machine problems during operation, and regular maintenance shall be done. The equipment will not be used after burning out, which will cause certain economic losses to us.　　 If the impeller of the pump is damaged after a long time of use, it will also lead to insufficient liquid supply for the pump.

　　What should be paid attention to in the process? Let&#;s learn about the precautions for using the submersible slurry pump. When the equipment is in use, the pump itself generally needs to be placed on land for use, but its suction pipe needs to be placed in waterSales Department,　　As a submersible slurry pump widely used in many fields, it has the advantages of simple structure, convenient disassembly and maintenance, and convenient installation and use. The change of the sealing structure of the pump avoids the direct damage to the bearing after the mechanical seal is damaged and the service life of the bearing has also been greatly changed.　　 number of lifting pipes　　 The slurry pump mainly aims at conveying flow, so the flow meter (meter) shall be installed in the operation monitoring system as far as possible to monitor whether the flow meets the requirements at any time; In the pipeline system, slag flushing system and pressure filtration dehydration system equipped with hydrocyclone, certainRobat Karim, there is generally only outgoing cable, and the user needs to connect it separately during installation. If the connection is wrong, it will seriously affect the normal operation of the pump, so we should follow the correct steps to connect.　　Although the shaft seal occupies a small position in the pump, the normal operation of the pump is closely related to the shaft seal.　　Promote the continuous expansion of the sales network group.