In order to ensure the demand for water and electricity for production and living, many units, hotels and residential areas in various provinces and cities in China have purchased it and generators. Many enterprises have also purchased generators out of their own pockets in order not to delay production. Driven by this it and the generator naturally become popular　　When the water level reaches, the frequency of the frequency converter drops, and the slurry pump operates at a low speed. The higher the water level, the lower the speed; The lower the water level, the higher the speed. At the same time, the circulation in the slag slurry pool is basically unchangedIonia,　　 whether pre lubrication water tank is required　　 Another possibility is that the gas is sucked in when the pump is in use.San Felipe,IoniaCarbon steel explosion-proof pipeline pump,　　Work no noise and vibration, and the site is cleaner.　　The above is about how to replace the water seal of Boshan submersible slurry pump. In addition to the water seal, other parts of the pump also need to be replaced in time when they are damaged. Moreover, some parts of the pump are relatively easy to be damaged, so we need to replace them regularly during use　　Check whether it needs to be replaced.　　The above is a brief introduction to the effect and form of shaft seal of submersible slurry pump. Users can choose the appropriate shaft seal type according to their actual needs.

　　Do a good job of fixing to avoid the motor falling into the water and directly scrapping.　　The reaction force will make the axial motor end of the pump retract, resulting in the collision between the static ring and the moving ring. The impact force at that moment is very large which can directly damage the dynamic and static rings of the mechanical seal.　　When this type of pump is used at ordinary times, the motor shaft will drive the impeller of the pump to rotate, and then at this time, the rotating force can be brought to the medium,IoniaLong shaft submerged slurry pump, so thatconsumption,　　The slurry pump should be larger. In addition to the existing industrial and mining applications of the vertical slurry pump, the submersible slurry pump can also be used as a mobile slurry pump, such as sand pumping and prospecting on board; What are the advantages of the submersible slurry pump? The advantage of the submersible slurry pump is that it is convenient and flexible, easy to operate and submerged　　 When the power supply voltage is too low, the pump will be overloaded, because the pump is also widely used in many rural watering. In this case,IoniaWater well pipeline pump, it may be lower than the rated voltage, so the current in the stator winding will also be　　The direction of the differential pressure force is opposite, which can offset part of the axial force and prolong the service life of the bearing.

　　There is a difference between submersible slurry pump and sewage pump. Although the media conveyed by the two are not pure water and other media, the difference between slag slurry and sewage is still large. Let&#;s take a look at the difference between the two.Customer first,　　The above introduction is about the cause ysis of the overload of the slurry pump. When we find these conditions when using the pump, we can check whether these reasons are the above. This is also a reminder that we need to maintain the pump during normal use. latent　　 Drain the water filled in the motor.　　 First, screw down the bolts on the side bearing pressure cap, and then remove the nuts used for the connection between the three parts: discharge section, stuffing box body and bearing body; Then screw off the round nut on the shaft, and successively install the bearing inner race, bearing gland and retaining sleeveIonia,　　Water or air leakage in the pipeline. The nut may not be tightened during installation. If the leakage is not serious, the air or water leakage can be treated with cement or cement slurry mixed with asphalt oil. Temporary repairs can be done with some wet mud or soft soap. If water leaks at the water pump joint, tighten the nut with a wrench. as　　Generally, the diving depth of the submersible slurry pump is not more than meters, and the operation is reliable. Why not more than meters? This is the crucial technical point of the submersible slurry pump, because the current sealing technology in China is more than meters, not because the slurry pump has a problem, but because　　The solution to the excessive temperature of the water pump: when selecting the motor, it is necessary to select one that matches its power and speed. In addition, but pay attention to adjusting the vacuum pump