Advantages of using I-beam: reduce maintenance cost reduce downtime, improve equipment operation rate, reduce equipment capacity and increase power consumptionDifference and application description between H-beam and I-beamAmir, Ditch cover plate (ditch cover plate) is widely used in municipal roads, garden facilities, residential quarters schools, stadium pipes and other places.The working principle of flat steel finishing machine in I-beam production process is to pre level and finally level the cold flat steel with two groups of leveling wheel sets staggered up and down in the thickness direction; A pair of finishing wheels arranged relatively are used to extrude the width direction, so that the width is compressed to achieve the expected parameters, and the compression amount is adjustable; Straighten the width with staggered straightening wheels.Panorama,H-section steelStages needing attention in the production and manufacture of alloy tubesThe flange of H-beam is of equal thickness, including rolling section and combined section composed of three plates welded. All I-beams are rolled sections. Due to poor production technology, the inner edge of the flange has a slope of : The rolling of H-beam is different from that of ordinary I-beam. Only one set of horizontal rolls is used. Because its flange is wide and has no inclination (or the inclination is very small), a group of vertical rolls must be added for rolling at the same time. Therefore, its rolling process and equipment are more complex than ordinary rolling mills. The maximum height of rolled H-section steel that can be produced in China is mm,Amir10Cr9Mo1VNb alloy pipe,AmirHow much is No. 14 I-beam per ton, which exceeds the welded composite section.

I-beam has the dual properties of high hardness and toughness materials. Compared with other engineering wear-resistant materials in China, such as various alloy steel plates, cast wear-resistant plates, cast stones,AmirGH536 alloy pipe, rubber, polyurethane, etc., it has irreplaceable comprehensive excellent properties.Due to the impact of poor visual . Only through the application of mesh and the overall stiffness can we see the potential of demand. The application of steel data is a high one, such as the reuse rate of mesh and reinforcement installed in the current mesh production company and the treatment of corrosion. The design strength value of circular reinforcement and the design strength value of welded reinforcement mesh. According to the equal strength substitution principle and considering comprehensive factors, the use of steel welded mesh plate can save the use of steel bars in the steel welded mesh plate factory. And the reinforcement mesh needs to be processed after it is shipped to the site, so there is no wear.→ wide flange and large lateral stiffness. Strong bending resistance.resources,Whether I-section steel is ordinary or light, because the section size is relatively high and narrow, so it can only be directly used for members bent in the plane of their web or form lattice stressed members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application. I-beam is widely used in buildings or other metal structures.I-beam can be divided into four types according to shape: cold-formed equal edge I-beam, cold-formed unequal edge I-beam, cold-formed inner crimping I-beam and cold-formed outer crimping I-beam.X-ray or ultrasonic testing shall be carried out for repair welding of alloy pipe, dead end welding of strip steel and circumferential seam. For the spiral welding of steel for the transportation of flammable general liquids, yibai%sx ray or ultrasonic testing shall be carried out. For the spiral welding of alloy pipes for the transportation of water, gas, heating steam and other general liquids, X-ray or ultrasonic testing sampling inspection (%) shall be carried out.

I-beam: national standard * what is the wall thickness of I-beamHighly recommended,Dry processing technology: after passivation treatment, parts shall be dried with air compression or hot gas, or drying treatment or air drying can be selected. Pipe installation Special rolling method. When it is difficult to roll the required I-beam by the usual rolling method for some reason, the special rolling method can be used to make full use of the skills of uneven deformation and pass design. For example, when the billet section is narrow and wide I-beam is required to be rolled, the wave rolling method can be used; for example, when the billet is wide and small I-beam is required to be rolled, the negative rolling method can be used Spread rolling, etc.Amir,The crack mainly occurs at -mm from the edge of the alloy pipe. The shape is several parallel vertical cracks of different sizes. The regularity is that the thicker the specification and model of the alloy pipe is The wider the width the more serious the disadvantages.I-beam features: the content of chromium carbon alloy is -%, the hardness of chromium carbide alloy is V, and the macro hardness is - HRCDefects of alloy pipe and solutions: