Each box, it is necessary to check the fuse for repair and replacement.Cologne,The overflow valve cannot be debugged on its own. The reason why hydraulic cargo elevators are slow is mainly due to human factors in the later stage. Therefore, attention should be paid to maintenance and upkeep during use to reduce accidentsAluminum alloy elevators are different from other forms. This type of elevator is made of aluminum alloy material, which is lightweight and has a more beautiful appearance. The disadvantage is that it has a light load capacity and is only suitable for simple high-altitude maintenance work, and can only provide support for - people.Bharatpur,The hydraulic lifting platform often checks the connection status of each part, and if there is any looseness,CologneGuide rail hydraulic lifting platform, it should be tightened. The connection bolts of the machine body should be checked for tightness when the elevator body is under pressure (the compression condition can be formed by rotating the arm). All connecting shafts need to have split pins and need to be fully opened.Oil leakage is a common malfunction. Due to loose joints or damaged sealing rings, oil leakage may occur. Therefore, this fault can be solved by tightening the oil leakage joint or replacing the damaged sealing ring.Considering the oil level in the oil tank, when all hydraulic cylinders in the system are extended, the oil level in the oil tank should not be lower than the Z-low oil level and when the oil cylinders retract, the oil level should not be higher than the Z-high oil level. In fact, most manufacturers have noticed the above issues. The reason for the introduction is that most users can learn more about the equipment itself when using elevators, in order to facilitate equipment maintenance. Hydraulic cargo elevator manufacturers sincerely hope that you choose a legitimate manufacturer when purchasing elevators, to avoid any worries about after-sales service.

The installation personnel should confirm and count the equipment details, confirm that there are no omissions in the shipped equipment details, check if the tools are complete, and ensure the smooth progress of the installation process.Oil cylinder leaks. Long term use causes wear on the sealing ring in the oil cylinder and excessive oil leakage in the cylinder wall gap, resulting in the natural descent of the hydraulic cargo elevator. The sealing components need to be replaced immediately.Pre install equipment maintain unobstructed access roads and sufficient parking space before pre installation. Some hydraulic cargo elevators require heavy lifting assistance for installation, some require equipment such as forklifts for installation, and some can be pre installed manually. When it is necessary to install with the assistance of a truck crane and a forklift, full consideration should be given to whether the on-site environment meets the working conditions of the truck crane.Home page recommendation,There are many reasons for unstable workbench descent, such as overload, unstable support, severe eccentric load, etc. In response to the above reasons, it can be solved by reducing the load, adjusting the center of gravity of the load, perform minor repairs to the mechanical and electrical systems.Before installation, the installation personnel should confirm the infrastructure such as the foundation and shaft, pay attention to alignment leveling, and alignment points, and confirm that the foundation meets the requirements before construction.

Do you know the classification of simple cargo elevator lifting platforms? The manufacturer of the hydraulic cargo elevator is here to inform you.Product range,The classification of lifting platforms is as follows: they are divided into mobile lifting platforms, automatic lifting platforms, hydraulic lifting platforms, folding arm lifting platforms, and sleeve type lifting platforms according to their different modes of movement.Ensure a good power supply at the installation site, install a separate distribution box, and when using the distribution box, the electrical leakage switch must meet the requirements for construction elevators. If the installed construction elevator is variable frequency the leakage switch should be compatible with the frequency converter when selecting it.When encountering signs of overheating in the electric motor, it is necessary to park the car in a timely manner, clean the problem, and continue running. The motor bearings should be smooth and outstanding.Cologne,Regularly check the operation of each mechanism for normal operation and noise. If any faults are found, the hydraulic cargo elevator wholesale should be promptly eliminated. Otherwise, it will affect the use of the guide rail hydraulic lifting platform. When refueling, the hydraulic oil should be filtered and filled,CologneHydraulic ladder,CologneGuide rail elevator, and the refueling tools should be reliable and clean. The hydraulic cargo elevator manufacturer should not remove the filter at the fuel tank filler to improve the refueling speed. Refueling personnel should use clean gloves and work clothes to prevent solid and fiber impurities from falling into the oil.Protective device: In case of power or oil circuit failure, there should be a safety rope to prevent the workbench from falling out of control. (Allow controlled descent)The classification of lifting platforms is as follows: they are divided into mobile lifting platforms, automatic lifting platforms, hydraulic lifting platforms, folding arm lifting platforms, and sleeve type lifting platforms according to their different modes of movement.