Optional configuration of fixed lifting platform: The fixed lifting platform can be equipped with auxiliary devices according to usage requirements, and can be combined in any combination such as the safety protection device of the fixed lifting platform; Electrical methods; Form of work platform; Power form, the coupling inside the oil cylinder is loose. The internal fault of the oil cylinder is that the installation of the oil cylinder motor is not concentric. From the motor etc. The correct selection of various configurations maximizes the functionality of the lifting platform and achieves effective use.The noise and oil level of the elevator oil cylinder are too low. From the air at the connection of the oil filter or joint to the oil, the air and oil at the moving shaft are blocked. The oil return pipe of the oil filter is loose, and the air or oil pipe is on the oil surface, Mixing air into the oil to eliminate: The concentricity should be adjusted to within .MM. The coupling should be repaired or the oil pump should be replaced to increase the oil volume above mm in the oil filter and joint positions. The rotating shaft sealing ring should be replaced to clean the oil filter screen, filter the oil, lock the return oil pipeline, and extend the return oil pipeline below the oil level. If there is air mixed in the oil or the air in the hydraulic cylinder is not completely discharged, it will cause cavitation under high pressure and cause significant noise. At this point, it is necessary to exhaust the air in a timely manner.Charlotte,Usage and instructions for steel wire ropes in elevators: The steel wire ropes of the steel wire ropes require very high strength, usually made of high-quality carbon steel with a carbon content of .% -.%. They are widely used as transmission components in elevators. Due to its large load-bearing capacity, smooth operation, suitable for high-speed transmission, high strength, strong overload capacity, and reliable operation, it has become a commonly used rope for hydraulic elevators.The elevator itself has a simple structure and is easy to maintain, which has been favored by a large number of enterprises and individual customers. Hydraulic elevator is a multifunctional heavy loading and unloading mechanical equipment. The lifting system of hydraulic elevators is driven by hydraulic pressure, also known as hydraulic powered elevators.Ostrava,The above are the working principles of three common elevators, and there are also some forms of elevators that are not common such as cylinder mounted elevators, curved arm elevators, car mounted elevators, etc. Their common feature is the hydraulic principle for operation, because the stability of the hydraulic system can bring better user experience and safer operation to the equipment,CharlotteFixed electric hydraulic lifting platform, it will cause leakage. Disassemble and clean the check valve, and replace it if necessary.After hours of elevator operation, carry out medium maintenance on the mechanical and electrical systems.

If the circuit of the device is not disconnected or lowered, it is necessary to check the fuse for repair and replacement.Many high-rise cargo transportation often requires the use of hydraulic cargo elevators or transport elevators, but in practical applications, there is a strange phenomenon that more people choose to use hydraulic cargo elevators than elevators. Why is this? We are a long-term elevator manufacturer that welcomes inquiriesIntroduction to the unloading lifting platform: The unloading lifting platform is a specialized auxiliary equipment used in conjunction with forklifts for cargo loading and unloading. With it, forklifts can directly drive from the ground into the interior of car compartments for batch loading and unloading operations. The warehouse unloading platform products use manual hydraulic power and do not require power supply. Only one person needs to operate to achieve safe and fast loading and unloading of goods. It can reduce a lot of labor, improve the efficiency of loading and unloading operations, speed up the flow of materials,CharlotteHydraulic scissor type lifting platform, and obtain greater economic benefits.analysis,Selection of the location of the loading and unloading lifting platform In order to reduce the cost of material handling, the location of the platform should be selected to minimize the distance of the handling tools and vehicles in the factory. It is much easier to move a fully loaded transport vehicle to a designated location outside the building than to transport the loaded materials one by one to the designated location indoors. When selecting a platform location, full consideration should be given to the production process and operational needs of the factory. There are two modes of platform layout: merging: loading and unloading on the same platform.Car mounted lifting platform: The car mounted lifting platform is designed to improve the mobility of the lifting platform by fixing it to a transport vehicle or truck. It receives power from the car engine and achieves the lifting function of the car mounted lifting platform. To adapt to high-altitude operations inside and outside the factory area.Therefore, in the hydraulic pipeline assembly line, it is necessary to avoid dead bends as much as possible and check the tightness of the sleeve in a timely manner.

The installation personnel should confirm and count the equipment details, confirm that there are no omissions in the shipped equipment details, check if the tools are complete, and ensure the smooth progress of the installation process.Respect for customers,Hydraulic lift cargo elevators belong to high-altitude work equipment. Small shaking of the scissor type structure is normal, operations above meters are generally allowed. Due to its own weight, devices above this height begin to vibrate in different ranges. The vibration range depends on factors such as weight, lifting height, and intensity of high-altitude operations.It is not allowed to throw tools and materials up and down, and ropes should be used to tie or hang them to avoid injuring workers or scaffolding below.Hydraulic lifting table: the hydraulic lifting table is widely used in various industrial enterprises and production lines such as automobile, container, mold manufacturing, wood processing,CharlotteSmall hydraulic lifting platform, chemical filling, etc., to meet the lifting needs of different operation heights, and can be equipped with various table forms (such as ball, roller, rotary table, steering, tipping, telescoping), and with various ways (separate, linkage, explosion-proof), it has stable and accurate lifting, frequent starting The characteristics of large load capacity effectively solve various lifting and lowering difficulties in industrial enterprises, making production operations smooth.Charlotte,Remove the hydraulic oil tank filler cap, filter cover, inspection hole, hydraulic oil pipe and other parts to avoid dust when removing the system oil pipe. Clean the disassembled parts before opening them. When disassembling the hydraulic oil tank filler cap, first remove the soil around the tank cap, loosen the tank cap, and remove any remaining debris from the joint (do not rinse with water to prevent water from seeping into the tank). After confirming cleaning, open the tank cap.To consider its capacity, and fixed equipment takes - times.The hydraulic lifting platform often checks the connection status of each part, and if there is any looseness it should be tightened. The connection bolts of the machine body should be checked for tightness when the elevator body is under pressure (the compression condition can be formed by rotating the arm). All connecting shafts need to have split pins and need to be fully opened.