DusseldorfAluminum alloy single column lifting platformAnalysis of industry emerging market representatives
release time:2024-02-12 22:48:43

Check the fastening status of the wall bracket, support rod, and bolts and retaining rings between the lifting cargo elevator and the bridge. If they are loose or displaced they should be checked and tightenedCheck the fastening status of the wall bracket, support rod, and bolts and retaining rings between the lifting cargo elevator and the bridge. If they are loose or displaced, they should be checked and tightenedDusseldorf,The driver shall close and lock the movable doors at both ends of the protective fence before work, and then ring the bell to start. It is strictly prohibited to work with the movable doors of the protective fence open. In case of special circumstances during platform operation, the emergency stop switch can be used to stop the platform. However, during normal operation,DusseldorfScissor fork mobile hydraulic lifting platform, it is prohibited to use the emergency stop switch to stop the platform.Manganese steel is generally used as the primary profile for warehouse cargo elevators. In order to achieve better anti-corrosion effect, a layer of rust resistant primer is usually applied, which effectively blocks air and prevents premature corrosion of the steel. Below, Ruilong hydraulic press will explain the role of rust resistant primer.Khoramshahr,When disassembling the hydraulic oil tank filler cap, filter cover, inspection hole hydraulic oil pipe and other parts, it is necessary to avoid dust during the system oil passage. The disassembled parts must be thoroughly cleaned before opening. When disassembling the hydraulic oil tank filler cap, first remove the soil around the tank cap. After loosening the tank cap, remove any remaining debris from the joint area (do not rinse with water to prevent water from seeping into the tank). Only after confirming cleanliness can the tank cap be opened. When using materials and hammers, materials that do not remove fiber impurities and specialized hammers with rubber attached to the surface should be selected. Hydraulic components and hydraulic hoses should be carefully cleaned, dried with high-pressure air, and then assembled. Choose a well packaged filter element (the inner packaging is damaged, although the filter element is intact, it may also be unclean). When changing the oil, clean the filter at the same time. Before installing the filter element, carefully clean the bottom dirt inside the filter housing with materials.Manganese steel is generally used as the primary profile for warehouse cargo elevators. In order to achieve better anti-corrosion effect, a layer of rust resistant primer is usually applied, which effectively blocks air and prevents premature corrosion of the steel. Below, Ruilong hydraulic press will explain the role of rust resistant primer.Organize, remove rust and repaint the structural components such as the suspension cage and guide rail frame for corrosion,DusseldorfLarge fixed lifting platform, and reinforce the severely corroded load-bearing members


DusseldorfAluminum alloy single column lifting platformAnalysis of industry emerging market representatives



Check the wear and clearance condition of the guide wheel of the cargo elevatorPower supply voltage: Motor power: Lifting: Rocker self reset switch operation Overload protection: Over current relay.Check the oil level of the gearbox and make up for new oil if necessarysuperior quality, with an oil temperature between and ℃. Use a large flow rate to remove impurities from the system as much as possible. The hydraulic system needs to be cleaned repeatedly three times or more. After each cleaning, fully drain the system while the oil is hot.


DusseldorfAluminum alloy single column lifting platformAnalysis of industry emerging market representatives



Monthly maintenance: View weekly inspection itemsCustomer first,When disassembling the hydraulic oil tank filler cap, filter cover, inspection hole, hydraulic oil pipe and other parts, first remove the soil around the tank cap. After loosening the tank cap, remove any remaining debris from the joint area (do not rinse with water to prevent water from seeping into the tank). Only after confirming cleanliness can the tank cap be opened. When using materials and hammers, materials that do not remove fiber impurities and specialized hammers with rubber attached to the surface should be selected. Hydraulic components and hydraulic hoses should be carefully cleaned, dried with high-pressure air, and then assembled. Choose a well packaged filter element (the inner packaging is damaged, although the filter element is intact, it may also be unclean). When changing the oil, clean the filter at the same time. Before installing the filter element, carefully clean the bottom dirt inside the filter housing with materials.According to calculations,DusseldorfSelf walking scissor fork lifting platform, when the support points of the beam type components are located along the length of /L on both sides, the vibration resistance is relatively small, making it easy to obtain resonance and vibration effects with larger amplitudes. The geometric shape of the structure on the lifting foundation is similar to a long beam type component, and the structure is complex. Therefore, two support points should be taken on each side for time treatment.  ?? Hidden danger investigation relies on joint efforts from all aspects:?? Construction enterprises are the main responsibility for identifying hidden dangers in construction elevators. They should strengthen daily inspections and regular inspections, and carefully inspect the steel structure, safety protection devices, electrical devices, and transmission devices of construction elevatorsDusseldorf,The wear rate is fast, and due to factors such as processing, assembly, and adjustment of new machine components, the friction surface is rough, the mating surface area is small, and the surface pressure condition is uneven. During the operation of the machine the concave and convex parts on the surface of the parts are intertwined and rubbed against each other. The metal debris that falls off from the grinding process, in turn, acts as abrasive and continues to participate in friction, further accelerating the wear of the mating surface of the parts. Therefore, it is easy to cause wear on components (especially the mating surface), with a fast wear rate. At this point, if overloaded, it may cause damage to the components and lead to early failures.Regularly check all wires and cables for damage. Timely bandage and replace damaged parts.Regularly check whether the operation of each mechanism is normal and whether there is any noise. If any faults are found they must be promptly eliminated.


comment list
  • Iron ore underground mining

    It's worthy of praise, really good, DusseldorfAluminum alloy single column lifting platform I like it very much.

  • Pastry Sales

    I didn’t expect online shopping to be so interesting. Under the guidance of the seller, I finally learned online DusseldorfAluminum alloy single column lifting platform, thank you!

  • Wynn Films

    DusseldorfAluminum alloy single column lifting platform Very good, good quality and low price, express delivery is also fast, and inspection is also very standard.

©2009-2024Metal Microblog  Sitemap