The contact opening and closing of the travel switch of each safety device must be reliable, and the contact arc crater should be polished in time.Regular maintenance Regularly check whether the circuit system of the hydraulic lifting platform is loose, and check whether the wires and cables are aging and damaged, which may cause leakage of the line. If there is, it should be repaired in time to avoid electric shock.Columbus,The daily maintenance of guide rail lifting equipment should pay attention to regular inspection and maintenance, eliminate hidden dangers, and eliminate faults. Doing this is good for improving work efficiency, prolonging the service life of equipment and ensuring the safety performance of the elevator.Secondly, there must be no dirt on the friction surface. If there is dirt, it needs to be washed off with gasoline or thinner; the gear box, gearbox, replace them in time. If there is any looseness, it should be tightened in time. The connecting bolts of the equipment should be checked for tightness when the body is under pressure. All connecting shafts should be equipped with cotter pins; check whether each mechanism is operating normally, whether there is noise or failure , dismantling and adjusting the slewing mechanism of the equipment, it is necessary to pay attention to the parallelism between the reducer and the center line of the gear, and the appropriate meshing gap; conduct a comprehensive inspection of the equipment regularly, whether the wires and cables are If there is damage, whether the motor is overheated replace it in time and continue to run after troubleshooting; ensure that the bearings of the motor, each box, distribution box and brushes must be kept clean, and the travel switch points of each safety device must be safe and reliable.Beni-Mellal,Hydraulic system: mainly oil cylinders, high-strength chrome-plated rods, Japanese NOK seals, self-made external integrated pump stations, oil pipelines, solenoid valves, etc. The Japanese NOK seal used in the oil cylinder has good wear resistance, which ensures that the oil cylinder series will not leak oil for a long time. The gear pump pumps the oil in the oil tank into the oil circuit and enters the oil cylinder, thereby driving the top of the rod and raising the equipment; The valve is used to adjust the oil output, the ascending and descending speed, and contains an emergency descending device to ensure that the guide rail hydraulic lifting platform can descend safely in case of an emergency.Always check all wires and cables for damage. The damaged part should be bandaged and replaced in time.What are the maintenance rules for hydraulic lift machinery? The brakes of each mechanism should be checked frequently and the gap between the brake shoe and the brake wheel should be adjusted to ensure flexibility and reliability. There should be no dirt on the friction surface, and if there is dirt it must be washed off with gasoline or thinner.

As for the guide rail elevator installed outdoors, it is often exposed to rain and sunlight so special attention should be paid to regular maintenance and inspection to avoid accidents.Seat belts Seat belts must be inspected once every six months,Columbus1 ton lifting cargo elevator, and they must be inspected or replaced by relevant units. It is strictly forbidden to use seat belts that have expired. When working in the following environments you should wear seat belts: In the scene where high-altitude operations are required, when entering the workplace , Workers must wear safety belts; when working at heights exceeding two meters, they must wear safety belts; in working environments where scaffolding is not used or there is no fence on the scaffolding, safety belts must be used when the working height exceeds meters; Safety belts must be used when working on the roof; on the top floor of a flat house, safety belts must be used when there is no protective fence within meters from the edge of the roof or the roof opening; the platform or workbench is in a suspended state; Safety belts must be used if there are openings on the ground near the roof or ladders; safety belts must be used when working at heights without safe fall prevention measures.This kind of fixed lifting equipment can also be used in the warehouse. For example, a certain floor in the warehouse needs to be lifted to send goods or personnel into the designated warehouse.Quality inspection report,Test the freight elevator every day to see if the freight elevator can operate normally.Naturally connect the motor to the lift. When connecting,ColumbusCustomized lifting cargo elevator, it must be ensured that the concentricity of the output shaft of the elevator is consistent with that of the input shaft of the motor, and that the outer flanges of the two are parallel. If the concentricity is inconsistent,ColumbusFactory freight elevator lifting, it will cause the motor shaft to break or the elevator gear to wear.Uses: The scissor-type fixed lifting platform is mostly used for the transportation of goods between the height differences of the production line, the loading and unloading of materials, the adjustment of the working height during the assembly of the workpiece, the feeding of the installed machine at a high place, the lifting of parts during the assembly of large equipment, and the storage and unloading place and Forklifts and other handling vehicles are used for fast loading and unloading of goods, car lifting, fixed three-dimensional parking and other places.

Conscientiously write the special construction plan for installation and construction, and make safety technical disclosures to the installers.For more, please check, no one should stand around to watch.Manual hydraulic platform classification: Manual hydraulic lifting platform vehicles can be divided into manual hydraulic handling platform vehicles, manual hydraulic stacking platform vehicles, and manual hydraulic scissor platform vehicles.When the freight elevator breaks down, professionals should be invited to repair it, and the freight elevator cannot be altered without authorization.Columbus,The daily maintenance of the hydraulic lifting platform in normal use is essential, but even if there is normal maintenance on the equipment, any possible problem cannot be ignored, so in order to ensure that the process of using the hydraulic lifting platform for each operation What aspects do we need to check before operation? Today, the editor will give you a popular science.Frequently check whether the various mechanisms are operating normally and whether there is any noise. If a fault is found, it must be eliminated in time.Safety performance: The lifting structure is made of high-strength manganese steel rectangular tube, and the scissor-type mechanical mechanism is easy to maintain, with strong stability and high carrying capacity. The maximum lifting height is about meters, and the maximum load is about tons. .