When installing,Colorado SpringsMast type aluminum alloy hydraulic lifting platform, disassembling, and adjusting the rotating mechanism, attention should be paid to ensuring that the middle line is parallel to the middle line of the gear, and its meshing surface is not less than %. The meshing clearance should be suitable for the brakes of each mechanism. The clearance between the brake wheels should be regularly checked and adjusted to ensure its flexibility and reliability. There must be no dirt on the friction surface and it must be cleaned with gasoline or diluent.There is noise inside the hydraulic cylinder. When replacing the hydraulic oil, it is easy to generate cavitation and high-frequency noise. When the rod is bent or replaced with a new seal, the new seal is too tight, which can also produce significant noise. If it is a problem of tight sealing, the noise can be reduced after running in for a period of time. If the rod is bent, it needs to be corrected. In addition, hydraulic pipelines should use hoses as much as possible even when arranging pipelines, it can reduce vibration and noise,Low power consumption: Hydraulic elevators are driven by the pressure generated by their own weight, greatly saving energy. Long term improvement of various brand products such as elevator manufacturers with complete designated products and quality assuranceThe hydraulic elevator overflow valve can also generate high noise. When air is mixed in hydraulic oil, the overflow valve is stuck or severely worn, the spring of the overflow valve is fatigued and deformed, resulting in unstable pressure regulation of the overflow valve, and the relief time of the overflow valve is too short, it is easy to cause the pilot valve performance of the overflow valve to be partially stable, causing air to vibrate inside the pilot valve and generate noise. So we need to regularly clean the overflow valve. When the overflow valve is damaged or severely worn, it should be replaced.Mingguru Province,The undercut length of the weld mm should not exceed % of the weld seam, and the depth should not exceed .mm.Do not use hydraulic lifting equipment with malfunctioning issues. The problem should be resolved before carrying cargo.The guide rail type elevator has a structure of a straight top oil cylinder. The linear operation of the oil cylinder pulls the transmission chain, driving the lifting of the table to complete the operation. The guide rail type elevator is a popular form of cargo elevator in recent years, with the advantages of higher lifting height, stable operation, and simple maintenance compared to the scissor fork type elevator.

Considering the oil level in the oil tank, when all hydraulic cylinders in the system are extended, the oil level in the oil tank should not be lower than the Z-low oil level, and when the oil cylinders retract, the oil level should not be higher than the Z-high oil level. In fact, most manufacturers have noticed the above issues. The reason for the introduction is that most users can learn more about the equipment itself when using elevators, in order to facilitate equipment maintenance. Hydraulic cargo elevator manufacturers sincerely hope that you choose a legitimate manufacturer when purchasing elevators, to avoid any worries about after-sales service.Firstly, it will naturally be corroded by oxides and acidic gases. This requires us to apply an appropriate amount of grease to protect it from erosion as a weight component. If we change the oil, we must open the box and use it for a long time to prevent the hydraulic cylinder from being used for a long time. In the operation of hydraulic cylinders, the speed should be appropriate and should not exceed m/s to extend the service life of the hydraulic cylinder. In addition, in order to protect the mechanism and safety, it is very important to install buffer devices internally to protect the hydraulic cylinder. The greater the pressure of the protective hydraulic cylinder, the heavier the load, and the greater its pressure. A specialized product manufacturing enterprise that integrates research and development as well as service. A long-term professional elevator manufacturerThe elevator is evenly distributed at any position on the guide rail at % of the maximum load capacity, and should be stable at the maximum lifting height.details,The hydraulic oil used in the system has the same brand, and the oil temperature is between ~ ℃. Use a large flow rate to remove impurities from the system as much as possible. The hydraulic system needs to be cleaned repeatedly three times or more, and after each cleaning, the system should be drained while the oil is hot. After cleaning, clean the filter and add new oil after using a new filter element.This paper briefly introduces some matters needing attention in the selection of oil tank for hydraulic elevators. The main functions of the hydraulic oil tank for elevators in the hydraulic system of elevators and hydraulic elevators and other hydraulic machinery are oil storage heat dissipation, separation of air contained in oil and elimination of foam.When the hydraulic oil is insufficient, the hydraulic pump will experience suction, causing air to enter the hydraulic oil and producing high noise.

The installation personnel should have the qualification for installing hydraulic cargo elevators, and provide safety technical disclosure to the installation personnel for technical design.Where can I find it?,The main device does not engage. When this fault occurs check whether the three-phase power supply is normal, whether the internal and external emergency stop button switches,Colorado SpringsScissor type hydraulic lifting platform, the electric lock switch are turned on, whether the three-phase electrical phase sequence is correct, and whether the relay working indicator light is on.The so-called input hydraulic energy refers to the input flow rate and pressure, and the output machinery is the speed and traction force during linear motion. All these parameters are achieved through changes in working volume, so hydraulic cylinders are a type of volumetric actuator. In order to meet the different needs of various machinery, hydraulic cylinders have different structures and hydraulic capabilities. According to hydraulic capacity, it can be divided into single acting hydraulic cylinders and double acting hydraulic cylinders. According to its structural characteristics,Colorado SpringsHydraulic electric lifting platform, it can be divided into plunger hydraulic cylinders and hydraulic cylinders. Telescopic hydraulic cylinders and hydraulic cylinders are both referred to as the heart of hydraulic cargo elevators. How to maintain the heart of a hydraulic cargo elevator? Professional elevator manufacturers guarantee quality, service, and quality. Your satisfaction is our pursuit! Welcome to inquire by phoneThe combined platform is often used in small workshops with small volume of goods. However, because this platform needs to complete two functions at the same time, it inevitably increases the distance of handling tools/vehicles in the workshop.Colorado Springs,Remember not to overload, overload is the root cause of many faults.The elevator is evenly distributed at any position on the guide rail at % of the maximum load capacity, and should be stable at the maximum lifting height.The noise and oil level of the elevator oil cylinder are too low. From the air at the connection of the oil filter or joint to the oil, the coupling inside the oil cylinder is loose. The internal fault of the oil cylinder is that the installation of the oil cylinder motor is not concentric. From the motor, the air and oil at the moving shaft are blocked. The oil return pipe of the oil filter is loose, and the air or oil pipe is on the oil surface, Mixing air into the oil to eliminate: The concentricity should be adjusted to within .MM. The coupling should be repaired or the oil pump should be replaced to increase the oil volume above mm in the oil filter and joint positions. The rotating shaft sealing ring should be replaced to clean the oil filter screen, filter the oil, and extend the return oil pipeline below the oil level. If there is air mixed in the oil or the air in the hydraulic cylinder is not completely discharged, it will cause cavitation under high pressure and cause significant noise. At this point, it is necessary to exhaust the air in a timely manner.