It is strictly prohibited to connect the motor of the lifting platform to the wrong power supply. It should be ensured that the voltage is V or V, and daily cleaning work should be carried out. Dust and debris on the motor should be cleaned in a timely manner.Check the hydraulic oil quality and level. When the lifting platform is raised to a high position, the hydraulic oil level should be - millimeters higher than the bottom of the oil tank. When the color of the hydraulic oil darkens, the oil becomes sticky, or there are foreign objects such as gravel in the oil, the hydraulic oil should be replaced in a timely manner. The hydraulic system of the lifting platform should be checked for hydraulic and pipeline connections. If the pipeline is damaged,GreensboroElectric hydraulic lifting platform, it should be replaced immediately; When there is looseness in the connection part, tighten the pipe joint.Greensboro,Usually, the connection status of each part is checked, and if there is any looseness, it should be tightened. The tightness of the body connecting bolts should be checked when the body is under pressure. All connecting shafts must have split pins and must be fully unfolded.The inconsistent production dimensions of the hydraulic lifting platform support rods are a quality defect of the lifting platform equipment itself. It is recommended that the manufacturer replace them, as the probability of this situation occurring is relatively low.Zaysan,The pressure of the lifting platform is very important. When lifting goods the pressure of the lifting platform will test the weight of the goods. If it is overloaded, the general lifting platform will prompt, which serves as protection. Therefore, now lifting platforms are equipped with pressure gauges. Hydraulic machinery should remind everyone to pay attention to the following points: the precautions for using small lifting platforms are based on pressure. Their load-bearing capacity is very poor and their size is small. When using the lifting platform, it is necessary to pay attention to its use. If overloaded, it will cause structural damage to the lifting platform. We have mentioned this many times before when using it.Hydraulic boarding axle; Streamline” The open hinge joint design increases the welding area by more than three times compared to ordinary tubular joints, effectively extending the service life and simplifying maintenance.Novice operators: Due to their lack of understanding or lack of understanding of the operation methods of high-altitude work platforms such as mobile elevators, it is easy for them to make mistakes and cause equipment malfunctions. Operators in this area need to patiently learn and pass training before they can operate and use them.

Each department's electric brush should be kept clean, and the brush pressure should be adjusted to ensure that its area is not less than %Aging and deterioration of hydraulic oil; The solution is to replace the hydraulic oil.When encountering overheating in the electric motor during daily maintenance of the elevator, it is necessary to quickly park the car remove obstacles, and then continue running. The motor bearings should be smooth and excellent.retailer,The guide rail type cargo elevator has been inspected and debugged before leaving the factory, and all technical indicators have met the design requirements. When in use, only the power supply needs to be connected, and the hydraulic and electrical systems do not need to be adjusted.During use, the elevator should be placed on a solid and flat ground to prevent tipping during operation. Press&quo; Rising; Or&quo; Descending; Press the button to frequently check and maintain the various components of the elevator when lifting the workbench. If the workbench does not move, it should be immediately stopped for inspection. When the working pressure of the electric elevator is found to be too high or the sound is abnormal, it should be immediately shut down for inspection to avoid serious mechanical damage; Regularly check the working status of the shaft pin every month. If any loose shaft pin or screw is found,GreensboroImported hydraulic lifting platform, it must be locked tightly to prevent accidents caused by the shaft pin falling off.Elevators are now very popular among people and can easily transport goods to high-rise buildings. Among them, hydraulic elevators are more popular among people, and people can choose the one that suits them according to their actual situation. However,GreensboroCustomized hydraulic lifting platform, during normal work, it is important to pay attention to the lifting speed of hydraulic elevators and avoid making mistakes. So what factors will affect the lifting speed of hydraulic elevators?

When using the distribution box, the electric leakage switch meets the requirements for construction elevators. If the fixed elevator installed is variable frequency, the selection of the leakage switch should be compatible with the frequency converter.Quality improvement,Novice operators: Due to their lack of understanding or lack of understanding of the operation methods of high-altitude work platforms such as mobile elevators, it is easy for them to make mistakes and cause equipment malfunctions. Operators in this area need to patiently learn and pass training before they can operate and use them.Secondly, there should be no dirt on the friction surface. If there is any dirt, it needs to be washed off with gasoline or thinner; The reduction gearbox, gearbox, external meshing gear, and other parts of the equipment, as well as the hydraulic oil, must be tested according to the requirements in the table; The correct maintenance method for hydraulic guide rail elevators is to regularly check the steel wire ropes in various parts for any breakage or looseness. If this phenomenon is found, it should be replaced in a timely manner. The maintenance of the steel wire ropes must be strictly carried out in accordance with the specifications; Check the connection status of each part according to the braking regulations. If there is any looseness, it should be tightened in a timely manner. The tightness of the connecting bolts of the equipment should be checked when the body is under pressure. All connecting shafts should be equipped with split pins; According to regulations, check the normal operation of each mechanism, whether there is noise or malfunction, and promptly eliminate all faults; When installing, disassembling and adjusting the rotating mechanism of the equipment, it is important to ensure that the centerline of the reducer and gear is parallel, and ensure that all boxes, distribution boxes, in practical work, if we do not pay attention to detailed maintenance, accidents may occur. Therefore, we should pay attention to them when performing daily maintenance.Greensboro,Drain all the hydraulic oil in the oil tank, open the oil tank, take out the oil suction filter, clean it, and return it to the oil tank. Install it in its original position. Fill the fuel tank with new oil.There are three movable plates on both sides of the adjustment plate, which can effectively avoid accidentally injuring the toes of operators when the adjustment plate is lowered ensuring the safety of equipment use.Working at heights is a common practice nowadays, but it also has a certain degree of danger. So people invented hydraulic lifting platforms, which are more convenient to help people complete high-altitude operations. However, otherwise they can easily malfunction, which may lead to serious consequences. So what are the common faults of hydraulic lifting platforms?