No matter what type of slurry pump you need, Ritter pump will provide you with high-quality slurry pump products; New progress in submersible slurry pump technology in recent years The diving depth has increased from meters to meters!　　 When the slurry pump fails to absorb water during operation it may also be because the bottom valve is not opened. At this time, it is necessary to check whether the bottom valve is open and make corresponding adjustment.Sucre,　　 water　　Troubleshooting: first increase the water pressure,SucreTwo stage slurry pump, then inject water into the pump body, and then start the pump. At the same time, check whether the check valve is tight and whether the pipes and joints leak. If air leakage is found, apply lubricating oil or mixed paint on the joint after disassembly, and tighten the screws.Bristol,　　The fruit is also bad; When the axial flow pump is used, its water output is relatively large, but the head is not too high, so the effect of using the submersible slurry pump in many plain areas is also relatively good; The water output and head of the mixed flow pump are actually derived from one　　Balance of.　　There is no need to equip auxiliary mixing or spraying equipment, and the operation is simpler. The equipment is directly submerged for operation, without noise and vibration, and the site is cleaner.

　　The high-efficiency slurry pump has three characteristics: first, the slurry pump has high operation efficiency and low loss.　　The equipment of this series of sewage pumps can be fixed or mobile. When the fixed active equipment is selected, the chain cable shall be separately threaded into (against the pump outlet, and its connection shall be parallel to the pump outlet) two eyebolts or lifting plates to lift the electric pump up and down. Evenly and slowly along the guide rail　　 Precautions for disassembly of submersible slurry pump Before disassembling the filter press, make sure that the liquid in the submersible slurry pump is completely discharged. If the rotor is disassembled, drain the lubricating oil in the rotor bearing housing. If the newly added oil is stored, it should continue to be used after maintenance. Do not dump it directlydiscount,　　The purpose is to avoid water leakage of the pump but the water seal may be damaged due to faults after being used for a period of time. Let&#;s learn how to replace the water seal.　　The submersible slurry pump may be blocked when it is used at ordinary times. In particular,SucreWater well pipeline pump, some equipment is frequently used at ordinary times, but the maintenance work is not done well when it is used, so it will be blocked after being used for a period of time　　We also need to limit the starting frequency and select appropriate thermal protection devices for use.

　　Body. So that the pump can realize high concentration transmission without auxiliary devices. The unique sealing device can effectively balance the pressure inside and outside the oil chamber,　　The of descending axial force can be used for slurry transportation in power plants, hydraulic and other professions; The mechanical seal is tight and reliable, and the leakage probability does not exceed drops /min, which is mostly used to transport flammable, explosive toxic, strong corrosive and valuable liquids or materials with high temperature, high pressure and low temperature.　　 When the slurry pump operates, it rotates at a high speed, once it reverses, the force will directly push the impeller to the outside, and the impeller collides with the sheath and guard plate. If the speed is high, the force ratio is low　　The submersible slurry pump and equipment can also choose to add some water inlet detection devices according to the actual use needs. The overheat monitoring devices are often used in a large amount in time, and the pump and motor of the equipment used in time are the same shaft, soSucre,　　After that, before starting again, check whether the impeller rolling is normal and whether the bearing assembly compression bolts are tightened, and then start the pump.　　Turn on the power supply type fool operation; It has a wide range of applications. In many cases, it belongs to a portable workstation,SucreHorizontal non clogging sewage pump, which can be brought wherever it is needed, because it does not need too many auxiliary facilities.　　 repair and level the welding part of the submersible slurry pump with a file, clean the part to be bound with alcohol again and wipe it dry.