The above introduction is about the cause ysis of the overload of the slurry pump. When we find these conditions when using the pump, we can check whether these reasons are the above. This is also a reminder that we need to maintain the pump during normal use. latent　　Body. So that the pump can realize high concentration transmission without auxiliary devices. The unique sealing device can effectively balance the pressure inside and outside the oil chamber, so that the pressure at both ends of the mechanical seal can be kept balanced, which maximizes the reliable operation of the mechanical seal and greatly extends its service lifeBarakibarak,　　From the working principle, Li is a centrifugal pump. The slurry pump can also be divided into other different types from other angles. Let&#;s see from what angle Panshi pump can classify the slurry pump: first, the suction inlet of the slurry pump　　It needs to be replaced in case of damage, swelling and deformation, insufficient spring pressure,BarakibarakSubmersible non clogging sewage pump,BarakibarakIrrigation deep well pump, etc.Gobernador Galvez,　　Friction. Because if the surface of the pump is smooth when it is used, the equipment will consume less energy when it is used. Generally, the submersible slurry pump and impeller are sprayed with polymer composite materials for use　　What stands out is the sealing of the container. The seal is easy to install and maintain, stable and reliable, but the price is quite expensive.　　Now you know the reason why the pump has air turbidity. In fact this is a very common phenomenon. You don&#;t have to worry about it. Water pump can transport many things, such as water, oil, liquid metal, the reasons for the motor heating of the submersible slurry pump are the above items. If the motor heating occurs, you can find the reasons from the above items. However, it must be noted that if the fault is caused by electricity, people who do not know electricity should not repair it by themselves, so as to avoid people　　Therefore, it can be directly installed in the sewage tank without building a special pump room to install pumps and machines, which can save a lot of land and infrastructure costs.　　Circumference. In the application of slurry pump, we must pay attention to reasonable design, correct calculation and appropriate type selection, which are very important. In addition to the main wheel, a set of stirring impeller is added at the bottom of the product, which can spray the precipitated slag into a mixture of water and solid particlesManufacturing cost,　　 To ensure the efficient operation of the submerged slurry pump, the clearance between the impeller and the front guard plate must be adjusted regularly to keep it between (.-mm). In addition to monitoring the flow and pressure during the operation of the pump, the motor shall not exceed the rated current of the motor. Monitor oil seal and bearing at any time　　 Assembly of rotor parts of submersible slurry pump Before assembly, apply a layer of lubricating oil on the mounting surface to protect the shaft hole from damage.　　Therefore, when the pump temperature is too high, you don&#;t need to panic. You can quickly troubleshoot according to the above-mentioned reasons, so as to find out the root cause of the excessive temperature of the equipment in time, the axial force is mainly composed of the pressure difference force of the liquid effect on the impeller and the gravity of the whole rolling part. The effect direction of the two forces is the same, and the resultant force is the sum of the two forces. If the submersible slurry pump is equipped with an auxiliary impeller, the liquid effect is on the auxiliary impellersafety requirements ,　　Screw it down, and then remove the bearing inner race, O-ring, shaft sleeve and retaining sleeve in turn.　　For example, /c-ah slurry pump is a small-diameter slurry pump without impeller removal ring. When it is necessary to remove the impeller we only need to fix the pump shaft, rotate the impeller in the opposite direction according to the rotation direction on the pump body, and then the impeller can be easily removed　　 When starting the slurry pump the outlet gate valve shall be (closed or slightly opened by /. Before starting the slurry pump, expand the pump inlet valve and close the pump outlet valve. Then start the pump. After the pump is started, slowly start the pump outlet valve. The size and speed of opening the pump outlet valve should be based on the fact that the pump does not vibrate and the motorBarakibarak,　　During normal operation, the temperature of the motor is very high, some even as high as ℃. In this case, it is easy to burn the motor and replace it with a new one. In fact, one motor burns out at this time. Don&#;t worry about replacing it. You must find out the cause of the motor&#;s heating, or　　 Move the sand pumping site frequently. When the pump pumps sand at a fixed position and drops to a certain height, lift the submersible slurry pump and move it to the adjacent position of the previous sand pumping place to continue pumping sand, so as to move the sand pumping place back and forth for sand pumping,BarakibarakQuotation slurry pump, so that the sand pumping area in this area forms a honeycomb, the submersible slurry pump can also be used as a mobile slurry pump such as sand pumping and prospecting on board; What are the advantages of the submersible slurry pump? The advantage of the submersible slurry pump is that it is convenient and flexible, easy to operate and submerged